background image

Part No. 890034                                                                                                                                                                     Form No. F101000A

Page 7 of 12

Before turning machine off, use the Tamper to slowly push
remaining pieces of wood through the chipper.  This can
prevent any remaining wood from jamming in the chipper when
machine is turned off.
Do not leave tamper on the ground, store tamper in the chipper
hopper.

Using two people to lift machine is recommended.  Lift holding the
handle and front of nozzle.  Secure in place during transport.

Never store engine indoors or in enclosed poorly ventilated

areas with fuel in tank, where fuel fumes may reach an open
flame, spark  or pilot light, as on a furnace, water heater, clothes
dryer or other gas appliance.

If engine is to be unused for 30 days or more, prepare as
follows:

Be sure engine is cool.  Do not smoke. Remove all

gasoline from carburetor and fuel tank to prevent gum deposits
from forming on these parts and causing possible malfunction of
engine. Drain fuel outdoors, into an approved container, away
from open flame.   Run engine until fuel tank is empty and
engine runs out of gasoline.

NOTE:  

Fuel stabilizer (such as Sta-Bil) is an acceptable

alternative in minimizing the formation of fuel gum deposits
during storage.  Add stabilizer to gasoline in fuel tank or storage
container.  Always follow mix ratio found on stabilizer container.
Run engine at least 10 min. after adding stabilizer to allow it to
reach the carburetor.

Do not store with debris in bag.

16.11

OPERATION

  

continued

TAMPER-TKD ONLY

16.8

16

HANDLING & TRANSPORTING:

STORAGE

16.4

Tamper Storage Position

GROUND SPEED

 can be varied by applying slight downward

pressure to handle during operation (to allow drive wheels
partial slippage) or by changing the engine rpm.

For improved control in confined areas, this machine can be
freewheel pushed forward or backward by releasing the
operator's bail and pushing machine.

This vacuum is self-propelled. To engage the drive, pull
operator's bail against operator's handle. The drive is disen-
gaged by releasing the operator's bail.(See figure at right)

PROPULSION

16.9

Handle

Bail

Bail
Down
Engages
Drive

Bail Up
Disengages
Drive

Summary of Contents for TERMITE KD511SP













Reviews: