background image

 

   

   

Page 8 

 
Accessories 

 
Standard Spray Tip - 

Order No. 94-98-00... 

(for size see selection chart)

 

Adjustable Tip - 

Order No. JACT-... 

(for size see selection chart)

 

Super ZIP Tip - 

Order No. 90-98-0059... 

(for size see selection chart)

 

 
Tip base for Standard Tip - 

Order No. 0114-016020 

Tip base for adjustable tips - 

Order No. 93-98-541-300 

Tip base Super ZIP - 

Order No. 90-98-5901HPF 

 
Filter 200 mesh, red (qty. of 10) - 

Order No. 00-00-0001320 

Filter 100 mesh, yellow (qty. of 10) - 

Order No. 00-00-0001319 

Filter 50 mesh, white (qty. of 10) - 

Order No. 00-00-0001318 

 
Kit of gaskets 

(Pos. 2,5,6,8,31,33,34)

 - 

Order No. 0114-013559 

Repair kit 

(Pos. 1,2,3,5,6,8,31,33,34)

 - 

Order No. 0114-013560 

 
Tool Kit 

(hex wrench, multi purpose wrench, pull-off ring) -

 

Order No. 0114-018490 

Cleaning Brush - 

Order No. 82-469 

Metering and Mixing Cup (qty. of 50) - 

Order No. MC -1-K50 

Viscosity measuring cup DIN4 (qty. of 2) - 

Order No. 7000-114-K2 

Hand cleaner towels SCRUBS 

(6 buckets of 72 towels each)

 - Order No. 192218-K6 

Tip cleaning needle (qty. of 12) - 

Order No. JAC-90-D 

Gun oil, silicone-free (bottle of 75 ml) - 

Order No. 6-428 

Gun grease, silicone-free (tube of 50 g) - 

Order No. AGMD-010 

 

 
Gun Connection 

 

 

 

 

Ensure the maximum operating excess pressure generated by the pump does not 
exceed the maximum operating excess pressure of the gun ! 

 

 

If the maximum operating excess pressure of the equipment exceeds the one of the gun, the gun 
must not be connected. 
 
Once this has been checked the procedure will be as follows: 

 

• 

Connect high pressure hose of the equipment to swivel (30) of the gun. Check for tight 
connection. 

• 

Insert tip into tip grip protection. 

• 

Insert washer. 

• 

Tighten tip grip protection using a wrench. 

• 

If you are using a turning tip like Super ZIP or similar, check its allowed operating excess 
pressure and install according to installation instructions. 

• 

Start initial setup procedure of the pump according to the pump Service Manual. 

• 

Refer to all operating and safety precautions of this service manual and of the pump manual. 

 

Summary of Contents for 0114-013514















Reviews: