5
AIR NOZZLES
AIR PRESSURE RECOMMENDATIONS
AIR NOZZLE RECOMMENDATIONS:
The 93P and 905P Air Nozzles are most suitable
for conventional materials. Use of very low fluid
delivery rates with these Nozzles will produce a
narrower than normal fan pattern.
Use the 97P and 907P Air Nozzles for heavy bodied,
high solids materials and low fluid flow rates
with conventional materials. High flow rates
with light bodied materials may result in some
minor “smoking” or material build-up on the
face of these nozzles.
USE OF THE 95AS OR 97AS SIPHON NOZZLES IS
NOT RECOMMENDED WITH THE M1-G GRAVITY
FEED GUN.
ATOMIZING
TYPE OF MATERIAL
PSI
Light Stains, Inks
3-4
Primer/surfaces
5-6
Acrylic Enamels
7-8
Lacquers
7-8
Low VOC, Urethanes
8-10
HVLP AIR NOZZLE 96G
NOZZLE NOZZLE
REGULATOR
ATOMIZING
ATOMIZING
GUN INLET
PRESSURE
AIR FLOW (SCFM) PRESSURE (PSI) PRESSURE (PSI)
(PSI)
7.5
3.0
23.0
35.0
14.0
5.0
29.0
42.0
15.5
7.0
33.0
47.0
17.5
9.0
39.0
55.0
19.0
10.0
43.0
60.0
HVLP AIR NOZZLE 94P
NOZZLE NOZZLE
GUN
INLET
AIR FLOW
ATOMIZING
PRESSURE
(SCFM)
(PSI)
(PSI)
7.0
3.0
14.0
9.0
5.0
21.0
11.0
7.0
27.0
12.0
9.0
30.0
13.0
10.0
33.0
LVLP AIR NOZZLE 93P
NOZZLE NOZZLE
REGULATOR
ATOMIZING
ATOMIZING
GUN INLET
PRESSURE
AIR FLOW (SCFM) PRESSURE (PSI) PRESSURE (PSI)
(PSI)
5.5
3.0
8.0
10.0
7.0
5.0
11.5
14.0
8.0
7.0
14.5
18.0
9.5
9.0
17.0
22.5
10.0
10.0
18.0
24.0
LVLP AIR NOZZLES 92P
NOZZLE NOZZLE
REGULATOR
ATOMIZING
ATOMIZING
GUN INLET
PRESSURE
AIR FLOW (SCFM) PRESSURE (PSI) PRESSURE (PSI)
(PSI)
4.5
3.0
6.0
9.0
6.0
5.0
8.5
10.0
6.8
7.0
11.5
14.0
7.5
9.0
13.5
18.0
8.0
10.0
15.0
19.0
92P and 93P are for general industrial and automotive finish applications.
HVLP AIR NOZZLES 95P, 97P, 95AP, 97AP, 905P, 907P
NOZZLE NOZZLE
REGULATOR
ATOMIZING
ATOMIZING
GUN INLET
PRESSURE
AIR FLOW (SCFM) PRESSURE (PSI) PRESSURE (PSI)
(PSI)
11.0
3.0
20.0
27.0
15.7
5.0
30.0
40.0
17.5
7.0
38.0
50.0
19.6
9.0
45.0
58.0
22.5
10.0
50.0
64.0
NOTE
Regulator pressures are based on 25' of 5/16"
Hose in good condition without Quick-
Disconnects or other restrictive fittings. Use
the Air Nozzle Test Gauge accessory to confirm
the atomizing/regulator pressure relationship
for your actual air supply set-up. These
recommendations are for “typical” or
“average” materials, and are intended to
serve as a starting point. Adjust as necessary
for your specific application.
Summary of Contents for M1-G HVLP
Page 10: ...10 NOTES ...
Page 11: ...NOTES 11 ...