Fast-Click Unlock Mode
Caution: Please set up your personalized
Fast-Click
Code after admin fingerprint
registration IMMEDIATELY.
Code Registration :
Fast-Click allows you to create a custom access code of short and long taps to manually un-lock
without a phone.
Set-up Guide: The Fast-Click code is a 6-digit code made up of a string of 6 long and short taps.
Example:
1.1 To enter the code registration mode:
- Tap and hold the hook for 5 seconds and wait for a flashing blue light, continue holding until
the red and blue light flashes.
1.2 Input your first Fast-Click digit:
- A long tap is greater than 1 second and less than 5 seconds, hold the hook until the red and
blue light turns on and that indicates a successful enrollment of a long tap.
- A short tap is less than 1 second, release the hook and that will activate a rapid flashing blue
light, indicates a successful enrollment of a short tap.
1.3 The red and blue light will flash rapidly after each successful enrollment.
1.4 Repeat step 2 until all 6 digits are successfully enrolled. After a code has been successfully
registered, a blue light will be activated and stay on for 4 seconds.
* Please write down your code after registration: __ __ __ __ __ __
Unlock Using Fast-Click Code or Change Your Code:
To Unlock:
2.1 Tap and hold the hook for 5 seconds and wait for a flashing blue light, continue holding until
the red and blue light flashes slowly.
2.2 Enter your registered code and wait until the blue light activates, that indicates the code is
entered correctly. The lock will be unlocked after 3 seconds.
2.3 If the code is entered incorrectly, a red light will be activated and turns into a slow flashing red
and blue light right after, then you can re-enter your registered Fast Click code.
* The lock will exit the Fast-Click Unlock Mode after 4 attempts of entering the wrong code.
Change Your Code:
3.1 Repeat the previous step 2.1,2.2 and tap the hook within 3 seconds after the blue light is
activated, then a rapid red blue light will flash, indicates a new code can be enrolled.
(The previous registered code will be erased automatically)
3.2 Repeat step 1.2,1.3 and 1.4 in Code Registration section to input your new Fast-Click Code.
Erase the Fast-Click code
The admin user of the lock can erase all the data including the registered Fast-Click Code
using the TouchLock App on the mobile devices.
4.1 Open the App and go to the “settings”.
4.2 Click on the “Reset to Factory” and type in the admin password.
FAQ :
- In the unlikely event the battery dies while locked, TouchLock BT should be charged using an
external battery to provide quick access to un-lock.
- For other questions or more instructions, please visit us
http://www.bio-key.com.hk/download.html
摩斯碼後備開鎖模式
注意 : 鎖注冊管理員后, 請立即設置摩斯密碼, 以防其它人搶先設置摩斯密碼
摩斯碼注冊
:
摩斯碼模式容許你建立一個自定的長同短碼組合的代碼
,
不需使用手機開鎖
.
設定指引
:
摩斯碼是以
6
位代碼
,
以一串
6
個長或短組合成
.
例子
:
1. 1
進入注冊摩斯碼模式
:
-
長按鎖鈎
5
秒
,
等到藍灯閃後
,
繼續按住鎖鈎直至紅藍灯快閃
.
2. 2
輸入你的摩斯碼
:
-
長碼是要按鎖鈎多於
1
秒
,
少於
5
秒
,
直到出現紅藍灯亮放手
,
顯示已成功輸入一個長碼
.
-
短碼是要按鎖鈎少於
1
秒放手
,
出現藍灯快閃
,
顯示已成功輸入一個短碼
.
1.3
每次成功輸入一個碼
,
紅藍灯會快閃
,
提示可以輸入下一個碼
.
1.4
重覆第
2
步直至成功輸入
6
個位的摩斯碼
,
當摩斯碼成功登入後
,
藍灯會亮起
4
秒
.
*
請注冊後
,
請記下你登入的代碼
: __ __ __ __ __ __
以摩斯碼開鎖或更改代碼
開鎖
:
2.1
長按鎖鈎
5
秒
,
等到藍灯閃後
,
繼續按住鎖鈎直至紅藍灯慢閃
.
2.2
輸入你已注冊的代碼
,
待藍灯亮後
,
顯示代碼輸入正確
,
三秒後會自動開鎖
.
2.3
如輸入錯誤
,
紅灯會亮起
,
然後會轉為紅藍灯慢閃
,
之後你可以重新再輸入已注冊的摩斯碼
.
*
如果四次輸入都錯誤
,
鎖會離開摩斯碼模式
.
更改你的代碼
3.1
重覆前面開鎖的第
1
和
2
步驟
,
在藍灯亮起的三秒內
,
按動鎖鈎
,
然後會出現紅藍灯快閃
,
顯示
一個新的摩斯碼可以注冊
(
之前已注冊的會自動刪除
).
3.2
重覆摩斯碼注冊的
2,3,4
步輸入新的摩斯碼
.
刪除摩斯碼
管理者用戶可以用手機上的
TOUCHLOCK APP
刪除所有資料
,
包括已注冊之摩斯碼
.
4.1
打開
APP,
進入
"SETTINGS (
設定
)"
4.2
點擊
"RESET TO FACTORY"
及輸入管理者密碼
.
FAQ :
-
如在不正常狀態下鎖上鎖了但没法打開鎖
,
請以外置充電器充電快速充電然後開鎖
.
-
其它問題或需要更詳細指示
,
請瀏覽我們網站
http://www.bio-key.com.hk/download.html