7
Having Problems? Don't go back to the store.
Call us
（0086） 571 8795 7615
for assistance.
M-F 8:00am-5:00pm PST English &
Chinese
1.
Turn off or disconnect all power to the wall junction
box serving the dispos
al
.
2.
Open the junction box in the wall and remove the wire
nuts or electrical tape or whatever is tying the old
dispos
al
wire to the electrical wire inside of the
junction box.
3.
Open the end bell plate at the bottom or the dispos
al
.
If you are using flexible armored (BX) cable:
1.
Install cable fitting in the dispos
al
end bell hole.
2.
Secure the cable to the fitting and install an insulating
bushing or equivalent.
If you are using nonmetallic-sheathed (ROMEX) cable:
1.
Install cable fitting in the end bell hole and secure the
cable to the fitting.
2.
Connect white wire from the junction box to the white
(or blue) wire of the dispos
al
.
3.
4.
Connect black wire from the junction box to the black
(or brown) wire of the dispos
al
.
Connect bare ground wire from the junction box to
green ground screw within the dispos
al
end bell.
If your power supply cable does not include a grounding
wire, one must be provided. Attach a copper wire
securely to the dispos
al
ground screw and attach other
end of ground wire to a metal cold water pipe. Do not
attach ground wire to a gas supply pipe. Use only UL
Listed grounding clamp. If plastic pipe is used in your
home, a qualified electrician should install a proper
ground.
PERMANENT WIRE INSTALLATION INSTRUCTIONS (CONTINUED)
TIPS FOR SUCCESSFUL OPERATION
A.
Be sure dispos
al
is empty before using your dishwasher so it may drain properly.
B.
You may want to leave the stopper in the sink drain when not in use to prevent utensils and foreign objects from
falling into the dispos
al
.
C.
Your dispos
al
is ruggedly built to give you many years of trouble free service. It will handle all normal food
wastes, but it will NOT grind or dispose of such items as plastic, tin cans, bottle caps, glass, china, leather, cloth,
rubber, string, clam and oyster shells, aluminum foil or feathers.
The Anti-Jam Swivel Impellers make a clicking
sound as they initially swing into place. This
indicates normal operation.
A.
Remove sink stopper. Turn on a medium flow of cold
water.
B.
Turn switch to ON position; your motor is turning at full
speed and ready to use.
C.
Scrape in food waste. Down the drain go table scraps,
peelings, rinds, seeds, pits, small bones and coffee
grounds. To speed up
garbage disposal
, cut or
break up large bones, rinds and cobs. Large bones
and fibrous waste require considerable grinding time
and are more easily thrown away with other trash.
Do not be alarmed that the dispos
al
slows down
while grinding. The dispos
al
is actually increasing
torque (grinding power) and is operating under
normal conditions.
D.
Before turning the dispos
al
off, let water and dispos
al
run for approximately 15 seconds after shredding or
grinding stops. This assures that all waste is thoroughly
flushed through trap and drain.
E.
It is not recommended to use hot water while running
dispos
al
. Cold water will keep waste and fats solid so
dispos
al
can flush away particles.
3.
Connect white wire from the junction box to the white
(or blue) wire of the dispos
al
.
4.
Connect black wire from the junction box to the black
(or brown) wire of the dispos
al
.
5.
Connect bare ground wire from the junction box to
green ground screw within the disposer end bell.
8.
OPERATING INSTRUCTIONS
9. CLEANING AND MAINTENANCE
DO NOT ATTEMPT TO LUBRICATE YOUR
DISPOS
AL
!
The motor is permanently lubricated. The dispos
al
is self
cleaning and scours its internal parts with each use.
NEVER put lye or chemical drain cleaners into
the dispos
al
, as they cause serious corrosion of metal
parts. If used, resulting damage can be easily detected
and all
warranties are void. Mineral deposits from your
water can form on the stainless steel turntable, giving the
appearance of rust. DO NOT BE ALARMED, the
stainless steel turntables used will not corrode.
