background image

 

 

Operation Manual BioSmart PV-WM v.029.1|03.2021|en 

 

Page 4 of 24

 

BioSmart PV-WM Reader  

Operation Manual 

1

 

Description of Reader Operation 

 

Purpose 

The  BioSmart  PV-WM  reader  is  used  as  part  of  the  BioSmart  biometric  access  control  and 

management system in accordance with the BioSmart UniPass controller. 

The BioSmart PV-WM reader is intended to read biometric data of a human palm vein pattern and 

RFID-tag (card) code with subsequent transfer of the read information to the BioSmart UniPass or BioSmart 
UniPass-EX controller via Ethernet. 

The device is intended for use in premises, the operating conditions in which correspond to those 

specified in this OM. 

The device can be used outdoors if the following conditions are met: 

 

installation  is  carried  out  in  accordance  with  the  requirements  of  this  manual,  taking  into 

account the provision of protection against dust and moisture penetration; 

 

the reader is used in conjunction with a protective visor for 

 

BioSmart PV-WM; 

 

the operating conditions of the reader do not go beyond the operational limits (see par. 2.1). 

 

Technical Characteristics 

Technical characteristics are in the Table 1. 
Table 1 

 Reader technical characteristics 

Parameter 

Value 

Biometric ID 

Palm vein 

Biometric Scanner Type 

Optical, infrared 

Built-in RFID tag reader 

Yes 

Communication interface with the control computer 

Ethernet (IEEE 802.3u, 

100BASE-TX) 

Maximum cable lenght Ethernet, m 

100 

Indicators 

Buzzer and LED indicator 

DC supply voltage, V 

12 ± 15

 % 

Maximum consumed current, A 

0,4 

PoE support 

IEEE 802.3af class 3 

Case material 

Palstic 

Dimensions, mm 

185 x 160 x 134 

Net weight, g 

550 

Gross weight, g 

880 

Ambient temperature during operation, °С

 

From -40 to +50 

The upper value of the relative air humidity during operation at 
a temperature of 25 

С

, % 

95 

Enclosure protection 

IP65 

 

Depending  on  the  format  of  the  RFID-tags  (cards)  used,  appropriate  versions  of  the  readers  are 

provided. The list of versions is given in Table 2. 

The list of RFID-tags formats read by BioSmart PV-WM, depending on the version of the reader, is 

given in the reader's passport. 

Table 2 

 List of the BioSmart PV-WM reader versions Construction 

Execution 

Note 

BioSmart PV-WM-EM 

For reading EM-Marine format card 

BioSmart PV-WM-MF 

For reading Mifare format card  

BioSmart PV-WM-LG 

For reading Legic format card 

BioSmart PV-WM-IC 

For reading HID iClass format card 

Summary of Contents for PV-WM-MFR

























Reviews: