background image

global.BISSELL.com   

11

Problem

Possible Cause

Remedies

Reduced or no 

spray

Clean water tank may be 

empty.

Fill tank with hot tap water.

Tank may not be seated 

completely.

Turn power OFF. Remove and reseat tank.

Pump may have lost prime.

Turn power OFF and then back ON. Wait one 

minute, then press trigger.

Debris filter on base is 

clogged.

Turn power OFF. Use hand to remove debris.

DirtLifter® 

PowerBrush 

does not turn

The belt is off or broken.

Turn power OFF and unplug machine from 

outlet. Follow instructions on page 9.

The machine is in the upright 

position.

Brushes only rotate when machine is reclined 

using the recline handle.

Circuit breaker on machine 

may have tripped.

Turn the machine OFF and unplug from outlet. 

Check to see if foreign object is caught in brush 

roll. Remove object. Plug machine in to reset 

circuit breaker.

Cleaner not 

picking up 

solution

Tanks may not be seated 

properly.

Turn the machine OFF. Pick up both the clean 

and dirty water tanks and reseat them so they 

fit snugly on the machine.

Hose cap may not be snapped 

into place.

Turn the machine OFF. Ensure hose cap is 

placed on machine tightly and will not come off.

Clean water tank is empty.

Check fluid levels in clean water tank and refill 

if necessary.

Dirty water tank has picked up 

the maximum amount.

Empty dirty water tank.

Red float “door” in the tank 

may have closed as a result of 

bumping an object or moving 

machine back and forth too 

quickly.

Turn the machine OFF, allowing red float door 

to release into the open position. Turn the 

machine back ON to continue cleaning. Be 

sure your forward and backward strokes are 

completed at a slower pace.

Front nozzle of machine is 

clogged.

Turn the machine OFF. Use fingers to remove 

any debris from this area.

Upper body filter is clogged.

Turn the machine OFF. Use fingers to remove 

any debris from this area.

WARNING 

To reduce the risk of electric shock, turn power OFF and disconnect plug from electrical outlet 

before performing maintenance or troubleshooting checks.

Troubleshooting

 Below are some of the issues you may run into. If you don’t see the 

issue you’re experiencing below, visit 

BISSELL-commercial.co.uk

.

  

  

  

Summary of Contents for 64P8 Series













Reviews: