Bissell 64P8 Series Manual Download | Manualshive

Page: 4 / 12

background image

4

global.BISSELL.com

Assembly

Your machine comes fully assembled. Before first use, ensure tanks are firmy in place and any inserts

are removed from the dirty water tank.

1.

Wrap cord around holder.

2.

Slide clean and dirty water

tanks into place.

3.

Remove any inserts from

the dirty water tank.

4.

Push the dirty water tank

handle back until it locks in

place with a click.

5.

Ensure hose latch is closed

completely to avoid suction

issues.

«
...
2
3
4
5
6
...
»

Summary of Contents for 64P8 Series













Reviews:

No comments

Related manuals for 64P8 Series

Brand: Kärcher Pages: 248

Brand: Kärcher Pages: 184

Brand: Kärcher Pages: 28

Brand: U.S. Products Pages: 20

Brand: M-system Pages: 2

Brand: Pacific Pages: 19

Brand: Pacific Pages: 20

PS 40 Powerscrubber

Brand: Kärcher Pages: 8

Brand: Kärcher Pages: 32

Brand: Kärcher Pages: 6

Nautilus MX3-200HE

Brand: Hydro-Force Pages: 55

Nautilus MX3-500H

Brand: Hydro-Force Pages: 57

Brand: parktool Pages: 2

Brand: Axminster Pages: 32

Brand: Kärcher Pages: 63

Brand: Pacific Pages: 12

Brand: Wirbel Pages: 208

Brand: KUKKO Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands