background image

10

1. Plan activities to give carpet tim e to dry.

2. Rem ove easily m oved furniture from  the room  ( chairs,

lam ps, coffee tables, etc) .

3. Vacuum  thoroughly to pick up loose debris and pet hair

before using the POWERSTEAMER

®

PROHEAT

PLUS.

4. Plan your cleaning route to leave an exit path. It is best to

begin cleaning in the corner farthest from  your exit.

Mac hine Preparation

5. Set up the m achine following instructions in 

The Basic s

section, pages 5-9.

6. Use Fiber Cleansing Form ula

in the Sm artMix

®

tank.

7. Choose the Sm artMix

®

setting to m atch the cleaning job.

8. Set the ReadyTools

switch on to either 

Tools/PreTreat

or 

Floor Clean in g.

Pre-Treating ( Optional)

Im proves cleaning effectiveness for heavily soiled carpet 

in high traffic areas such as entryways and hallways:

9. Set the Sm artMix

®

dial to 

High Traffic.

10. Set the ReadyTools

switch on 

PreTreat.

11. Plug into a proper outlet and turn ON both the Power 

and the Sm artTem p

switches.

12. While pressing the trigger, slowly m ake several passes 

over the area to be cleaned.

Cau tion : Do n ot overwet.

13. Turn the m achine Power switches OFF and let BISSELL

Fiber Cleansing Form ula

dissolve the tough soil for 

1-2 m inutes before continuing. 

Normal Cleaning

14. Plug into a proper outlet and turn the Power and the

Sm artTem p

switches ON.

15. While pressing the trigger m ake one slow forward and 

back wet pass. Let the Sm artTem p

heated form ula and

DirtLifter

®

PowerBrush

®

do the work for you.

Cau tion : Do n ot overwet.

16. Release the trigger and m ake one slow forward and back

pass over the sam e area to rem ove any residual dirty water.

How to clean car pets

17. Repeat cleaning passes until solution being

pulled up appears clean.

18. Continue passes without pressing the trigger

until you can’t see any m ore water being 

pulled up.

NOTE: Both the Sm artMix

®

an d the clean

water tan k m u st have liqu id in
them  in  order for the m achin e to
spray. If on e tan k is em pty the
m achin e will n ot apply either
clean in g solu tion  or water on ly.

19. After cleaning, you m ay want to turn the

Sm artMix

®

to 

Water On ly

to give your 

carpeting a final rinse. This will insure 

thorough rem oval of em bedded dirt loosened 

by the Fiber Cleansing Form ula.

20. When the cleaning job is com plete refer to 

the 

Maintenanc e/Putting it Away

section 

for m achine cleanup and storage 

instructions, page 14.

Summary of Contents for POWERSTEAMER PROHEAT PLUS 16981 Series



















Reviews: