background image

11

How to clean upholster y and small ar eas

Manufac turer’s Tag

Tip:

Deep c leaning 
c arpeting and
upholstery 
regularly c an
reduc e dust and
allergens in 
your home.

Important - Chec k Upholstery Tags:

1. Check m anufacturer’s tag before cleaning. “W” or “WS”

on the tag m eans you can use your POWERSTEAMER

®

PROHEAT

PLUS. If the tag is coded with “X” or “S” ( with a

diagonal strike through) , or says “Dry Clean Only,” do not

proceed. Do not use on velvet or silk. If m anufacturer’s tag

is m issing or not coded, check with your furniture dealer. 

2. Check for colorfastness in an inconspicuous place.

3. If possible, check upholstery stuffing. Colored stuffing

m ay bleed through fabric when wet.

4. Plan activities to give upholstery tim e to dry.

5. Vacuum  thoroughly to pick up loose debris and pet hair.

Use a vacuum  with a brush attachm ent and a crevice tool

to clean in fabric folds and tufts.

Mac hine Preparation:

6. Set up the m achine following instructions in 

The Basic s

section, pages 5-9.

7. Use Fiber Cleansing Form ula

in the Sm artMix

®

tank.

8. Set the ReadyTools

switch on 

Tools an d PreTreat.

*  Sm a rtTem p

hea ts the clea n in g solu tion  for ca rpet

a n d  b a refloor a pplica tion  on ly. It d oes n ot hea t 
solu tion  spra yed  throu gh the a ccessory tools.

9. Set Sm artMix

®

to 

Norm al.

Cleaning Tec hnique

1 0. Choose the 4” Sm all Area Tool, the Tough Stain Brush, or

the Spraying Crevice Tool and connect to the flex hose.

1 1. Plug into a proper outlet and turn the Power switch ON.

1 2. While pressing the trigger, slowly m ove the spraying tool

back and forth over the soiled surface. Release the trigger

to vacuum  soiled water.

1 3. Continue to clean soiled area, working in sm all sections,

until no m ore dirt can be rem oved.

Cau tion : Do n ot overwet.

1 4. When the cleaning job is com plete refer to the 

Putting 

it Away 

section for m achine cleanup and storage 

instructions, page 14.

Tip:

Try pre-treating

stairs or entry
ways with 
BISSELL Tough
Stain PreCleaner.

Then deep 
c lean with the
SmartMix

®

dial set on 

High Traffic.

Summary of Contents for POWERSTEAMER PROHEAT PLUS 16981 Series



















Reviews: