background image

 

 Magicians SOCD Cleaner V2 

 

  

Section 2: Safety & Modding Disclaimer

 

   

 

 

 

 

INSTALLATION MANUAL & USER GUIDE 

         REV B 

PAGE 2 

 

Section 2: Safety & Modding Disclaimer 

 
This product is to be used in a bigger electrical installation. It requires some basic 
knowledge of mechanical and electrical systems from you, the modder. While the 
necessary skills are not difficult to learn, it is still required for a successful installation. 
Some precautions to be mindful of are listed below. It is by no means an exhaustive list 
but is a step in the right direction. 
 

1. 

Always wear safety glasses to prevent debris from flying into your eyes when 
altering material by drilling, cutting, grinding, etc. 
 

2. 

Always use the right tool for the right job. For example, using a lighter instead of a 
heat gun to heat shrink a solder connection may work but it is not the suggested 
practice as there is a risk of fire and the release of noxious fumes. 

 

3. 

Always work in a well-ventilated area when the modding activity might release 
airborne debris or fumes. A mask or fume extractor may be required if modding in a 
small space or if there is an excess of debris or fumes. 

 

4. 

Always treat electricity with respect. Just because it is low voltage does not mean 
damage to you or to the equipment is not possible. 

 

5. 

Always disconnect power while modding. If you need make measurements or 
observe a behavior, make sure that wiring and equipment are secured enough to 
not cause them to move in an unfavorable manner where damage may result, and 
then connect power. 

 

6. 

Always use a fuse with battery mods. If the battery is rechargeable, always make 
sure that the charging and protection circuits are in place before using. 

 

7. 

Always double check polarity with reliable documentation or a multimeter wherever 
necessary. 
 

8. 

Never start modding something when you’re not confident you understand the 
process. Ask for help instead from the modding community or contact us. 

 
When properly installed, this product will not cause damage to your existing equipment or 
system. We are not responsible or liable for damage of any kind from improper installation 
practices. By continuing with this installation manual, you accept the risks and agree that 
you are proficient in making a successful installation. 
 
You also agree to have fun! Modding is a fun hobby to learn new things and building 
something cool, and to be proud of. Don’t let this page scare you! We are here to help 
every step of the way, and the community is extremely friendly so don’t be afraid to ask 
any questions you may have. 

Summary of Contents for Magicians SOCD

























Reviews: