background image

BITalino Mini 

User Manual  

 

 

  

 

 21 of 

24 

 

The user should not immerse the sensors or the 

BITalino

 device, nor clean with liquid 

or abrasives. 
 

The user should handle the 

BITalino

 device with caution and not expose the device or 

accessories to high accelerations and vibrations. 
 

BITalino

 devices should not be used in patients with implanted electronic devices of any 

kind,  including  pace-makers,  electronic  infusion  pumps,  stimulators,  defibrillators  or 
similar. 
 

Do not apply electrodes over damaged or irritated skin. 
 

Do not use your device while charging its internal battery. 
 

 

6.2. Transportation and Storage 

Please  follow  these  recommendations  to  ensure  safe  transportation  and  storage  of  your 

BITalino

 equipment and sensors to prevent any damaging of your system. 

 
The 

BITalino

 equipment and sensors should be stored in the original box in a dry place when 

those are not being used. 
 

  Relative humidity: up to 95% with no condensation 

  Ambient temperature: 10°C to 30°C 

  Atmospheric pressure between 500hPa and 1060hPa 

 
Whenever the equipment needs to be transported, it should be placed in the original box, since 
this was designed and tested to ensure the equipment and accessories are securely stored. 
 
Take  care  while  handling  the  transportation  of  the  system  and  avoid  dropping  it,  since  the 
device is not shock-proof and should not be placed under stress or sudden acceleration. 
 

6.3. Cleaning 

Please  follow  these  cleaning  instructions  to  prevent  any  damage  of  the  system  or  the  user 
because of conducting cleaning methods that may cause any damage. 
 

  The 

BITalino

 and sensors should be visually checked before each use and cleaning 

process to ensure that no mechanical damage occurred. 

 

  The 

BITalino

 equipment and sensors (including the cables) should be cleaned with a 

slightly damp cloth or suitable absorbent paper, ensuring no liquid enters the equipment 
of sensors. Do not use detergent or any type of cleaning liquid as these may damage 
your equipment and/or sensor. 

 

  Do not clean or re-use detection surfaces (electrodes). They are only suitable for single 

use, and should be disposed of after usage except indicated otherwise. 

 
 

Summary of Contents for Mini Shield

























Reviews: