background image

BITalino Mini 

User Manual  

 

 

  

 

 23 of 

24 

 

3rd party  system  you’re connecting to the  device

.  Check  the  electrical  specifications  of 

both systems you want to connect to prevent any damage of the user(s) or the systems. 
 
In  the  case  of  warranty  voidance,  the  same  applies  that  we  expressly  disclaim  any  liability 
whatsoever  for  any  direct,  indirect,  consequential,  incidental  or  special damages,  including, 
without limitation, lost revenues, lost profits, losses resulting from business interruption or loss 
of  data,  regardless  of  the  form  of  action  or  legal  theory  under  which  the  liability  may  be 
asserted, even if advised of the possibility of such damages. 
 

7.4. Contact & Support 

Contact us if you are experiencing any problems that cannot be solved with the information 
given in the 

BITalino documentation

. 

 
Please  send  us  an  e-mail  with  precise  information  about  the  error  occurrence,  device 
configuration, and, if possible, screenshots of the problem t

support@plux.info

. 

 

7.5. Regulatory Disclaimer 

BITalino  products  are  intended  for  use  in  life  science  education  and  research 
applications; they are not medical devices nor are they intended for medical diagnosis, 
cure,  mitigation,  treatment  or  prevention  of  disease.

  we  expressly  disclaim  any  liability 

whatsoever  for  any  direct,  indirect,  consequential,  incidental  or  special damages,  including, 
without limitation, lost revenues, lost profits, losses resulting from business interruption or loss 
of  data,  regardless  of  the  form  of  action  or  legal  theory  under  which  the  liability  may  be 
asserted, even if advised of the possibility of such damages. 
 

 

Summary of Contents for Mini Shield

























Reviews: