Please stop using CYCLOPS2 immediately if any of the abnormal
situations is found. These might be caused by device or unknown failure.
・
Power indication is full but it will run out very soon after using.
・
The device turned very hot when been charged via AC adapter or
USB
port..
Charging the Battery:
CYCLOPS2 is installed with Lithium-ion battery but not fully charged. Please fully charge
it before the 1
st
time use under the environmental temperature of 5
℃～
35
℃
.
1. Charging with AC adapter:
You can charge CYCLOPS2 using the AC adapter via charging contacts. Please be
cautious on the orientation of the connection plug.
2. Charging with USB cable:
You can also start charging CYCLOPS2 through AC cable connected with USB port
of host device.
※
Do not operate CYCLOPS2 while it is being charged via USB port as the
power surge might damage the USB port.
※
The USB connection via AC cable can not be used for data transmission. It is for
battery charging purpose only.
※
It will take about 2.5-hr to fully charge CYCLOPS2 via the AC adapter.
※
It will take about 3-hr to fully charge CYCLOPS2 through USB port.
※
Please do not charge CYCLOPS2 through USB hub.
※
Please use ONLY the standard AC adapter in CYCLOPS2 box. It might cause
charging failure or damage the device if using other unauthorized AC adapter.
3. Charging Time:
Charging time required will vary depending on the actual application of CYCLOPS2
and the condition of CYCLOPS2 battery pack.
4. Life span of CYCLOPS2 Li-ion battery pack:
General life span of Li-ion battery pack is around 300 times charging/discharging
cycles.
Default System Value:
Mode: Real-Time Mode
Auto Power-OFF time: 3-min
Device Name: BTS700
＋
BT address last 4-digits
Authorization: No
BT Profile: HID
PIN Code: 0000
Encryption: No
Date & Time Setup: OFF
RESET to Default System Value:
●
Please scan the
“DEFAULT” setup barcode at
the right.
As the memory setup parameter cannot be deleted,
please initialize the memory first then delete the data
in the memory.
●
When CYCLOPS2 has been configured as
“ reverse barcode scanner”, please scan the
“reversed DEFAULT” setup barcode at the right.
Memory Initialization:
Memory Initialization will delete all data and values in the memory.
Please scan the barcode at the right side which can initialize the memory.
※
Please note:
there is no way to restore the data
deleted after memory initialization.
Simple ways to start CYCLOPS II:
1. Power ON
Press the SCAN button for 3-second to turn ON and Scan LED will light up as well.
After power ON, scan LED will go off and CYCLOPS2 is standing-by for scanning.
2. Power OFF
When CYCLOPS2 is standing-by for a period of time, it will be OFF automatically
(default: 3-min) to conserve battery power
. There is no “POWER” switch on
CYCLOPS2.
3. RESET to Default System Value
Please press the RESET button while CYCLOPS2 is ON (it will be OFF
automatically after been RESET).
4. Bluetooth Communication
Before using Bluetooth communication, please make Paring connection with the
host device.
Default PIN code is
“0000”. You can easily start connection through Bluetooth
host device and can be confirmed by the BT LED status indication.
Also, you can scan configuration barcodes to switch communication mode to SPP
Master.
5. Barcode Scanning
Please press the SCAN key to scan the barcode.
Scanning result can be confirmed by the SCAN LED
status. Scanning the setup barcode at the right to
confirm if CYCLOPS2 is able to scan.
Communication with iPad and iPhone:
Under default, you can easily connect iPad or iPhone using BT HID Profile. Software
keyboard on iPad or iPhone can be displayed or hidden by pressing the FUNCTION
key on CYCLOPS2.
Detailed Configuration Guide:
On our website, you can download the Detailed Configuration Guide. Please carefully
read the Guide to understand all the details about CYCLOPS2 and how to tailor this
device further into your applications.
http://www.bitatek.com.tw
Since the Configuration Guide can be shown on LCD monitor and CYCLOPS2 is
designed to read barcodes in various forms, on various media. You can scan those
configuration barcodes directly on LCD screen and set CYCLOPS2 up accordingly. It is
not necessary to print Configuration Guide on paper as hard copy for scanning purpose.
Duplication of Configuration Data:
You can easily duplicate the Configuration data from one CYCLOPS2 to the other unit.
This will provide an easy and accurate way for multiple units CYCLOPS2 operations.
1. Configure the first unit CYCLOPS2 through setup barcodes scanning.
2. Connect the first CYCLOPS2 unit with host device through USB cable to transfer
the Configuration data to host device (SYSTEM.CFG file).
3. Connect the other CYCLOPS2 unit with host device through USB cable to
download the configuration data from host device.
Long Term Storage of CYCLOPS2:
●
Please store this device in dry environment.
●
When the device is under Batch Mode and been kept OFF for an extended period of
time, Date & Time data might be RESET due to the battery power been drained.
●
Always charge CYCLOPS2 before using and refer to the Configuration Guide to set
Date & Time properly.
How to Dispose CYCLOPS2 Properly:
CYCLOPS2 is implemented with Li-ion battery which is recyclable and important
resource.
If you send CYCLOPS2 back to your supplier, it will be disassembled and the Li-ion
battery will be recycled. If you want to dispose this device by yourself, please remember
to pull out the battery and recycle it properly following regulations and rules set up by
your local authority.
●
The way to disassemble CYCLOPS2:
Remove the four screws on the back of CYCLOPS2.
Open the enclosure and remove the screws fixing the battery pack then you can pull
out the battery.
※
Notice when you are disassembling:
Please tape the metal part of the battery for proper insulation to avoid short-circuit.
Specification:
Model
：
Cyclops2
CPU
：
Atmel AT91SAM9G25 400MHz
Memory
：
32 MB Flash-ROM
Max 8,000 data files (fixed data size: 2048-Byte including
date & time ) can be saved.
128 MB SDRAM
USB
：
USB2.0 Full Speed
Bluetooth
：
Ver.2.1+EDR
Class2
（
10-m transmission range
）
including
SPP/ HID Profile
Scanner
：
CMOS Imager
（
2D
）
Motorola
SE4710 soft decode
RTC function
Yes, under Batch Mode only
Power Supply
：
：
Built-in Lithium-Ion battery
It will take about 2.5-hr to complete battery charge with AC
adapter. Battery life is about 8-hr ( QR-code, 256-Byte )
scan
※
1
I/O Interface
：
Micro USB-B type
AC Adapter
：
：
Input 100
～
240VAC, 50/60Hz
Output DC5V/2A, connector type: Micro USB
Operation
condition
Storage
condition
：
：
Temperature
–10
～
50
℃
( charging temperature 5
～
35
℃）
Humidity 20
～
85% without condensing
Temperature
-25
～
60
℃
Humidity 5
～
95%
Free Drop
：
1.5-meter
※
2
drop, and 1-meter Tumble Drop 100-Cycle
Sealing
：
IP-54
Regulatory
：
CE/ FCC
Dimensions
：
90
（
L
）
mm×38
（
W
）
mm×16
（
H
）
mm
Weight
：
About 67g
※
1
One scan per 6-second under room temperature and Bluetooth connection.
※
2
Free drop on concrete, 3 times per 6 surface at room temperature
Trademark
● Bluetooth & Logo are Trademarks of Bluetooth SIG, INC.
● iPad
、
iPhone and iOS are Trademarks of Apple Inc.
● ALL company name or logo appearing in this document are all intellectual property
rights of BITATEK CO.,LTD.
※
All copy rights are reserved: without any agreement of BITATEK, it is not allowed to
copy or quote any part or all content of this document.
Rev.1.2
CYCLOPS
