KT-200-2
41
y
Switch off the frequency inverter in
the control: Set
N
O
or
N
EIN
in menu
4.3.2 (
FI
USED
or
FU
AKTIV
).
y
Switch on the control in menu 3.2
(
M
ODE
or
M
ODUS
): Switch to
O
N
or
E
IN
.
y
Check current consumption of all
three phases.
y
Close the control panel cover.
A temporary emergency service is
possible if the compressor starts without
problems and the current consumption
does not show any excessive values.
However, the compressor contactor is
not designed for pulsed continuous
operation. Therefore, the time between
two compressor starts should be
increased to 7 minutes in menu 4.2.4.9
(
P
AUSE
M
IN
) (max. 8 starts per hour).
However, the FI should be replaced as
soon as possible.
Operation without speed regulator of
the condenser fans (N2)
If the speed regulator (N2) fails, the
condenser fans (M2 and M3) can be
switched on and off individually by
means of the control. Speed regulation
is impossible in this case.
y
Set the control to
O
FF
or
A
US
in menu
3.2 (
M
ODE
or
M
ODUS
).
y
制御中の周波数インバーターをオフ
にします。メニュー
4.3.2
(
FI
USED
または
FU
AKTIV
)で
N
O
または
N
EIN
に設定します。
y
メニュー
3.2
(
M
ODE
または
M
ODUS
)
で制御をオンにします。
O
N
または
E
IN
に切り換えます。
y
3
相すべての消費電流を点検してく
ださい。
y
コントロールパネルカバーを閉じます。
コンプレッサーが問題なく起動し、消費電
流が過度の値でない場合は、一時的な緊急
運転を行うことができます。ただし、コン
プレッサーコンタクターはパルス継続運
転に対応していません。そのため、
2
台の
コンプレッサーが起動する間の時間をメ
ニュー
4.2.4.9
(
P
AUSE
M
IN
)で
7
分に延長し
てください(
1
時間に最大
8
回の起動)。こ
れは緊急時の措置ですので、
FI
はできるだ
け早く交換してください。
コンデンサーファンの速度制御(
N2
)な
しでの運転
速度制御(
N2
)に異常がある場合、コン
デンサーファン(
M2
と
M3
)を制御に
よって個別にオン
/
オフにすることがで
きます。この場合、速度調節はできなく
なります。
y
メニュー
3.2
(
M
ODE
または
M
ODUS
)
で制御を
O
FF
または
A
US
に設定し
ます。
Caution!
High voltage!
The most terminals of terminal
strip X101 are energized by 230
V when condensing unit is
switched on:
警戒!
高い電圧がかかっています。
端子ストリップ
X101
のほとんどの
端子には、コンデンシングユニット
がオンになると
230 V
の電圧がか
かります。
y
Switch off the main switch.
y
Remove the main fuses.
y
Open the cover of the terminal box of
the condensing unit.
y
Bridge the speed regulator (N2):
Remove the cables of the contacts
1/L1 and 2/T1 on the speed regulator
and connect them electrically (cable
designations: T2F and T2FC).
y
Close the cover of the terminal box of
the condensing unit.
y
メインスイッチをオフにします。
y
メインヒューズを外します。
y
コンデンシングユニットの端子ボッ
クスカバーを開きます。
y
速度制御(
N2
)をブリッジします。
速度制御の接点
1/L1
と
2/T1
のケー
ブルを外し、それらを電気的に接続
します(ケーブル名:
T2F
と
T2FC
)
。
y
コンデンシングユニットの端子ボッ
クスカバーを閉じます。
Summary of Contents for ECOSTAR LHV6/2DC-3.F1
