background image

SRP-330/332III

 

Rev. 1.00

                                                                   

BIXOLON

 

 

-  51  -

 

FS p 

 

 

 

Function

 

:

 

Print NV bit image

 

 

 

Code

 

:

 

ASCII

 

FS

 

p

 

n

 

m

 

 

 

Hex

 

1C

 

70

 

n

 

m

 

 

 

Decimal

 

28

 

112

 

n

 

m

 

 

 

 

 

 

Range: 

1 ≤ n ≤ 255

 

0 ≤ m ≤ 3, 48 ≤ m ≤ 51

 

 

 

Default: 

None

 

 

 

Description

 

:

 

This command prints NV bit image n using the mode specified by m as follows:

 

m

 

Mode

 

0, 48

 

Normal

 

1, 49

 

Double-width

 

2, 50

 

Double-height

 

3, 51

 

Quadruple

 

 

 

 

Remarks

 

:

 

 

GS ( L and GS ( 8 can be used for printing NV bit image.

 

 

The NV bit image is defined by FS q.

 

 

n is assigned to each NV bit image to be stored in download order by FS q.

 

 

This command has no effect with NV bit image not defined in advance.

 

 

In page mode, the NV bit image is saved without being printed.

 

 

The printer does not print the NV bit image that is beyond one line of print area.

 

 

When using unidirectional print mode, there will be no vertical misali gnment between the top and bottom parts of the 

 

printed pattern.

 

 
 
 
 
 
 

 

Summary of Contents for SRP-330III





















































































































Reviews: