background image

14

Limited One-Year Warranty

B&K  Precision  Corp.  warrants  to  the  original  purchaser  that  its  products  and  the  component  parts  thereof,  will  be  free  from 
defects in workmanship and materials for a period of one year from date of purchase.

B&K  Precision  Corp.  will,  without  charge,  repair  or  replace,  at  its  option,  defective  product  or  component  parts.  Returned 
product must be accompanied by proof of the purchase date in the form of a sales receipt.

To obtain warranty coverage in the U.S.A., this product must be registered by completing a warranty registration form online at 
www.bkprecision.com within fifteen (15) days of purchase.

Exclusions:  This  warranty  does  not  apply  in  the  event  of  misuse  or  abuse  of  the  product  or  as  a  result  of 
unauthorized alterations or repairs. The warranty is void if the serial number is altered, defaced or removed.

B&K  Precision  Corp.  shall  not  be  liable  for  any  consequential  damages,  including  without  limitation  damages  resulting  from 
loss of use. Some states do not allow limitations of incidental or consequential damages. So the above limitation or exclusion 
may not apply to you.

This warranty gives you specific rights and you may have other rights, which vary from state-to-state.

B&K Precision Corp.
22820 Savi Ranch Parkway
Yorba Linda, CA 92887
www.bkprecision.com
714-921-9095

Summary of Contents for 1671A
























Reviews: