BK Radio KAA 0701 User Manual Download

Page: 12 / 15

- 9 -

Cloned Picklist Values

KNG Source

D & G

Standard

D & G

CMD

KNG-S/

KNG

Tone selected

Default values

TX Default set to 0,

Picklist reference #

and RX default value

Default values and

Picklist references

No tone selected

Default values

KNG-S Source

D & G

Standard

D & G

CMD

KNG-S/

KNG

Tone selected

Value of selected

CG tone/NAC

TX Default set to 0,

picklist reference #

and RX default value

Default values and

Picklist references

No tone selected

Default values

D/GPH-CMD Source

KNG-S/KNG

Tone selected

TX Default set to 0, picklist

reference #

and RX default value

No tone selected

Default values

If the cloning process fails or the target radio’s zone is blocked from

accepting an incoming clone, a fail message will appear on the Source

radio.
Failure of downloading can be due to:

• Zone programmed to block clone
• Improper connection
• Failure to turn on the Target radio
• Legacy Target radio in programming Mode
• Incompatible Target radio
• Cable unplugged

Summary of Contents for KAA 0701
















Search results

Summary of Contents for KAA 0701

Reviews:

Related manuals for KAA 0701

Brands by name

Popular brands

BK Radio KAA 0701, User Manual

Search results

Summary of Contents for KAA 0701

Reviews:

Related manuals for KAA 0701

Brands by name

Popular brands