background image

19

 

WHAT  IS  COVERED

This  warranty  covers  defects  in  material  and  workmanship  under  normal  use,  and  applies  only  to  the  original  purchaser 
providing  that:

The  equipment  has  not  been  accidentally  or  intentionally  damaged,  altered  or  misused;

The  equipment  is  properly  installed,  adjusted,  operated  and  maintained  in  accordance  with  National  and  local  codes.  and 
in  accordance  with  the  installation  instruction  provided  with  the  product;

The  serial  number  rating  plate  affixed  to  the  equipment  has  not  been  defaced  or  removed.

WHO  IS  COVERED

This  warranty  is  extended  to  the  original  purchaser  and  applies  only  to  equipment  purchased  for  use  in  the  U.S.A.

COVERAGE  PERIOD

Convection  Ovens:  COB  Models:  One  (1)  Year  limited  parts  and  labor;  COM  Models:  Two  (2)  Year  limited  parts  and  labor; 
Co1  Models:  Two  (2)  Year  limited  parts  and  labor;  (5)  Year  limited  door  warranty.
Warranty  period  begins  the  date  of  dealer  invoice  to  customer  or  ninety  (90)  days  after  shipment  date  from  BKI  -  whichever 
comes  first.

WARRANTY 

This  warranty  covers  on-site  labor,  parts  and  reasonable  travel  time  and  travel  expenses  of  the  authorized  service 

COVERAGE

representative  up  to  (100)  miles.  round  trip,  and  (2)  hours  travel  time. 

EXCEPTIONS

The  extended  door  warranty  years  3  through  5  is  a  parts  only  warranty  and  does  not  include  labor,  travel,  milage  or  any  other 
charges.

EXCLUSIONS

Negligence  or  acts  of  God,

Thermostat  calibrations  after  (30)  days  from  equipment  installation  date,

Air  and  Gas  adjustments,

Light  bulbs,

Glass  doors  and  door  adjustments.

Fuses,

Adjustments  to  burner  flames  and  cleaning  of  pilot  burners,   

Tightening  of  screws  or  fasteners.

Failures  caused  by  erratic  voltages  or  gas  supplies,

Unauthorized  repair  by  anyone  other  than  a  BKI  Factory  Authorized  Service  Center,

Damage  in  shipment,

Alteration,  misuse  or  improper  installation,

Thermostats  and  safety  valves  with  broken  capillary  tubes. 

Freight  -  other  than  normal  UPS  charges,

Ordinary  wear  and  tear.

INSTALLATION

Leveling.  as  well  as  proper  installation  and  check  out  of  all  new  equipment  -  per  appropriate  installation  and  use  materials  -  is 
the  responsibility  of  the  dealer  or  installer,  not  the  manufacturer.

REPLACEMENT 

BKI  genuine  Factory  OEM  parts  receive  a  (90)  day  materials  warranty  effective  from  the  date  of  installation  by  a  BKI  Factory 

PARTS   

Authorized  Service  Center.

This  Warranty  is  in  lieu  of  all  other  warranties,  expressed  or  implied,  and  all  other  obligations  or  liabilities  on  the  manufacturers  part.  BKI  shall  in  no 
event  be  liable  for  any  special,  indirect  or  consequential  damages,  or  in  any  event  for  damages  in  excess  of  the  purchase  price  of  the  unit.  The  repair  or 
replacement  of  proven  defective  parts  shall  constitute  a  fulfillment  of  all  obligations  under  the  terms  of  this  warranty.

7.  BKI  LIMITED  WARRANTY

PO  Box  80400      Simpsonville,  SC  29680-0400      USA

(864)  963-3471   

    Toll  Free:  (800)  927-6887   

    Fax:  (864)  963-5316

Form  #U4177A-BKI  7/07

Summary of Contents for CO1-E





















Reviews: