Before disposing of the battery, protect exposed terminals with heavy-duty electrical tape to prevent shorting
(shorting can result in injury or fire).
TROUBLESHOOTING
Problem
Solution
Unit Fails to Jump-Start
• Make sure unit’s power switch is in the ON position.
• Check that Jump-Starter has a full charge. Recharge unit if necessary.
• Make sure a proper polarity cable connection has been established.
• Leave charger plugged in and keep unit on charge for 24-48 hours.
USB Power Port will not power
appliance
• Make sure the USB Charging Port ON/OFF Pushbutton is in the ON
position.
• Check that Jump-Starter has a full charge. Recharge unit if necessary.
LED Area Light does not come on
• Make sure the LED Area Light ON/OFF button is in the ON position
• Check that Jump-Starter has a full charge. Recharge unit if necessary.
Portable Inflator will not inflate
• Make sure the Inflator Power Switch is in the ON position.
• Check that Jump-Starter has a full charge. Recharge unit if necessary.
• Make sure connector is pushed to valve stem and thumb latch is
closed when attempting to inflate tires; or nozzle (adapter) is securely
inserted into connector (chuck) on all other inflatables.
LED AREA LIGHT
The area light is controlled by the Area Light Power Switch on the front panel of the unit. Make sure the lamp is
turned OFF when the unit is being recharged or stored.
PORTABLE INFLATOR
The built-in 12 volt DC inflator is the ultimate inflator for all vehicle tires, trailer tires and recreational inflatables.
Three different sized nozzles are supplied. Each nozzle will clip on the end of the standard tire valve connector
located at the free end of the inflator hose. The inflator nozzles are stored inside the storage hatch on the top of
the unit. The inflator hose with tire fitting is stored in a retaining channel on the bottom of the unit. The ON/OFF
Switch is located on the front of the unit. The inflator can operate long enough to fill up to 3 average sized tires
before the battery must be recharged.
The inflator may be used by removing the air hose from the storage hatch and if required, fitting an appropriate
nozzle to the air hose. An ON/OFF switch located on the front of the unit controls the power to the inflator and the
gauge light. Refer to the “Controls and Indicators” section on page 5 for locations of inflator hose and nozzle
storage hatch. Return hose to the storage compartment after use.
WARNING: BURST HAZARD
• The inflator is capable of inflating up to 120 pounds per square inch (psi) pressure. To avoid over-inflation,
carefully follow instructions on articles to be inflated. Never exceed recommended pressures. Bursting articles
can cause serious injury.
• Always check pressure with the pressure gauge.
• Never leave the inflator unattended while in use.
CAUTION: RISK OF PROPERTY DAMAGE
Do not operate inflator continuously for extended periods of time (approximately 10 minutes, depending on
ambient temperatures), as it may overheat. In such event, inflator will automatically shut down. Immediately turn
OFF the Inflator Power Switch. Restart after a cooling down period of approximately 10 minutes.
Inflating Tires or Products With Valve Stems
1.Place connector (chuck) on valve stem.
2.Ensure connector is pushed on to valve stem as far as possible before closing thumb latch.
3.Make sure latch is secure.
4.Turn ON the Inflator Power Switch.
5.Check pressure with the pressure gauge.
6.When desired pressure is reached, open thumb latch and remove connector from valve stem.
7.Turn OFF Inflator Power Switch.
8.Allow unit to cool before storing away.
9.Store inflator hose and tire fitting in storage compartment.
Inflating Other Inflatables Without Valve Stems
Inflation of other items requires use of one of the adapters (nozzles).
1.Select the appropriate nozzle, located on the inside back cover.
2.Insert appropriate adapter (i.e. needle) into connector (chuck) and close thumb latch.
3.Small items such as volleyballs, footballs, etc. inflate very rapidly.
4.Insert adapter (i.e., needle) into item to inflate to appropriate pressure.
5.Turn ON the Inflator Power Switch — inflate to desired pressure or fullness.
6.Remove adapter.
7.Switch the Inflator Power Switch OFF.
8.Recharge the unit before storing away.
CARE AND MAINTENANCE
BLACK DECKER ACCESSORIES
GARAGE ACCESSORIES
