background image

GENERAL SAFETY RULES

WARNING:

Read and understand all instructions. Failure to follow all instructions
listed below may result in electric shock, fire and/or serious personal
injury.

SAVE THESE INSTRUCTIONS

WORK AREA
• Keep your work area clean and well lit. Cluttered benches and dark areas invite

accidents.

• Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or
fumes.

• Keep bystanders, children, and visitors away while operating a power tool.

Distractions can cause you to lose control.

ELECTRICAL SAFETY
• Double insulated tools are equipped with a polarized plug (one blade is wider than

the other.) This plug will fit in a polarized outlet only one way. If the plug does not fit
fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician
to install a polarized outlet. Do not change the plug in any way
. Double insulation 
eliminates the need for the three wire grounded power cord and grounded power supply
system.

• Avoid body contact with grounded surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if your body is grounded.

• Don’t expose power tools to rain or wet conditions. Water entering a power tool will

increase the risk of electric shock.

• Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an

outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace
damaged cords immediately. 
Damaged cords increase the risk of electric shock.

• When operating a power tool outside, use an outdoor extension cord marked "W-A"

or "W." These cords are rated for outdoor use and reduce the risk of electric shock. 

PERSONAL SAFETY
• Stay alert, watch what you are doing and use common sense when operating a power

tool. Do not use tool while tired or under the influence of drugs, alcohol, or
medication. 
A moment of inattention while operating power tools may result in serious
personal injury.

• Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your

hair, clothing, and gloves away from moving parts. Loose clothing, jewelry, or long hair
can be caught in moving parts. Air vents cover moving parts and should be avoided.

• Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with

your finger on the switch or plugging in tools that have the switch on invites accidents.

• Remove adjusting keys or wrenches before turning the tool on. A wrench or key that is

left attached to a rotating part of the tool may result in personal injury.

• Do not overreach. Keep proper footing and balance at all times. Proper footing and

balance enables better control of the tool in unexpected situations.

• Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes,

hard hat, or hearing protection must be used for appropriate conditions.

TOOL USE AND CARE
• Use clamps or other practical way to secure and support the workpiece to a stable

platform. Holding the work by hand or against your body is unstable and may lead to loss
of control.

• Do not force tool. Use the correct tool for your application. The correct tool will do the

job better and safer at the rate for which it is designed.

• Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled with

the switch is dangerous and must be repaired.

• Disconnect the plug from the power source before making any adjustments,

changing accessories, or storing the tool. Such preventative safety measures reduce
the risk of starting the tool accidentally.

• Store idle tools out of reach of children and other untrained persons. Tools are

dangerous in the hands of untrained users.

• Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained

tools, with sharp cutting edges are less likely to bind and are easier to control.

• Check for misalignment or binding of moving parts, breakage of parts, and any other

condition that may affect the tools operation. If damaged, have the tool serviced
before using. 
Many accidents are caused by poorly maintained tools.

• Use only accessories that are recommended by the manufacturer for your model.

Accessories that may be suitable for one tool, may become hazardous when used on
another tool.

SERVICE
• Tool service must be performed only by qualified repair personnel. Service or

maintenance performed by unqualified personnel could result in a risk of injury.

• When servicing a tool, use only identical replacement parts. Follow instructions in

the Maintenance section of this manual. Use of unauthorized parts or failure to follow
Maintenance Instructions may create a risk of electric shock or injury.

The label on your tool may include the following symbols.

V ..........................volts

A..........................amperes

Hz ........................hertz

W ........................watts

min ........................minutes

......................alternating current

......................direct current

no ........................no load speed

..........................Class II Construction

........................earthing terminal

........................safety alert symbol

.../min ..................revolutions or 

reciprocations
per minute

Safety Warnings and Instructions: Sanders

• ALWAYS WEAR EYE PROTECTION.
• Clean your tool out periodically.

WARNING:

Some dust created by power sanding, sawing, grinding, drilling, and other con-

struction activities contains chemicals known to cause cancer, birth defects or other reproduc-
tive harm. Some examples of these chemicals are:

• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and 
• arsenic and chromium from chemically-treated lumber (CCA).

Your risk from these exposures varies, depending on how often you do this type of work. To
reduce your exposure to these chemicals:  work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that are specially designed to filter out
microscopic particles.

Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and
other construction activities. Wear protective clothing and wash exposed areas with
soap and water. 

Allowing dust to get into your mouth, eyes, or lay on the skin may promote

absorption of harmful chemicals.

CAUTION: Wear appropriate hearing protection during use. Under some conditions

and duration of use, noise from this product may contribute to hearing loss.

CAT. NOs.  MS500

FORM NO. 582268-00   

PRINTED IN U.S.A.   

(NOV 02-1)

KEY INFORMATION YOU SHOULD KNOW:

• Never operate the sander without a recommended sanding sheet properly

installed on the base.

• The hook and loop pad and individual bases are replaceable parts. If they become

worn, return the unit to a local service center for repair.

• Do not push down—let the sander do the work. 
• Extended drywall sanding is not recommended for this product.

1-800-54-HOW-TO

BEFORE RETURNING THIS PRODUCT 

FOR ANY REASON PLEASE CALL

IF YOU SHOULD EXPERIENCE A PROBLEM

WITH YOUR BLACK & DECKER PURCHASE,

CALL 1-800-54-HOW-TO (1-800-544-6986).

IN MOST CASES, A BLACK & DECKER REPRESENTATIVE

CAN RESOLVE YOUR PROBLEM OVER THE PHONE.

IF YOU HAVE A SUGGESTION OR COMMENT,

GIVE US A CALL. YOUR FEEDBACK IS VITAL

TO THE SUCCESS OF BLACK & DECKER'S QUALITY 

IMPROVEMENT PROGRAM.

(544-6986)

VEA EL ESPAÑOL EN LA CONTRAPORTADA.

SAVE THIS MANUAL FOR FUTURE REFERENCE.

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA
DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES
DE USAR EL PRODUCTO. 

INSTRUCTION MANUAL

Catalog No. MS500

EXTENSION CORDS

When using an extension cord, be sure to use one heavy enough to carry the current your
product will draw. An undersized cord will cause a drop in line voltage resulting in loss of
power and overheating. The following table shows the correct size to use depending on cord
length and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the
gage number, the heavier the cord

SANDING LEAD BASED PAINT

Sanding of lead based paint is NOT RECOMMENDED due to the difficulty of controlling the
contaminated dust. The greatest danger of lead poisoning is to children and pregnant
women.
Since it is difficult to identify whether or not a paint contains lead without a chemical analysis,
we recommend the following precautions when sanding any paint: 

PERSONAL SAFETY

• No children or pregnant women should enter the work area where the paint sanding is being

done until all clean up is completed.

• A dust mask or respirator should be worn by all persons entering the work area. The filter

should be replaced daily or whenever the wearer has difficulty breathing.

• NOTE: Only those dust masks suitable for working with lead paint dust and fumes should

be used. Ordinary painting masks do not offer this protection. See your local hardware
dealer for the proper (NIOSH approved) mask.

• NO EATING, DRINKING or SMOKING should be done in the work area to prevent ingesting

contaminated paint particles. Workers should wash and clean up BEFORE eating, drinking
or smoking. Articles of food, drink, or smoking should not be left in the work area where dust
would settle on them.

ENVIRONMENTAL SAFETY

• Paint should be removed in such a manner as to minimize the amount of dust generated.
• Areas where paint removal is occurring should be sealed with plastic sheeting of 4 mils

thickness.

Minimum Gage for Cord Sets

Volts

Total Length of Cord in Feet

120V

0-25

26-50

51-100

101-150

240V

0-50

51-100

101-200

201-300

Ampere Rating
More

Not more

American Wire Gage

Than

Than

0

-

6

18

16

16

14

6

-

10

18

16

14

12

10

-

12

16

16

14

12

12

-

16

14

12

Not Recommended

R

2

1

Hook and Loop Pad

Tampon 

Almohadilla 

Sandpaper

Papier abrasif

Papel de lija

Pad Tip

Pointe de tampon

Punta de la almohadilla

Rotate 180°

Faire Tourner sur 180°

Gire180°

3

On Off Switch

Interrupteur

Interruptor de Encendido

Y Apagado

Extra Tips

Pointes supplémentaires

Puntas adicionales

R

4

Summary of Contents for 582268-00






Reviews: