Black & Decker All-In-One Horizontal B2000 Operating Instructions & Cook Book Download

Page: 10 / 32

the Baking Pan, slide a flat rubber or plastic spatula
along the sides of the pan to loosen the loaf. Turn
the pan over and shake the loaf out. Allow the bread

to cool before slicing. If the
Mixing Paddle remains in the

bottom of your loaf, allow the loaf to cool then use a
plastic spoon or rubber spatula to remove the pad-
dle. Do not use a knife or other sharp metal object
as this will scratch the non-stick coating on the
Mixing Paddle.

Using The “Add-Ingredient”
Function

All settings, except for RAPID bake, have a built-
in “Add-Ingredient” function which signals with

beeps when it’s time to add ingredients such as
fruits or nuts. The beeps sound before kneading is
complete to let you know it’s time to add the
ingredients. The actual time of the beeps can vary
up to 5 minutes depending on the room tempera-
ture at the time when you started the bread making
program. The following chart can be used for refer-
ence:

This function lets you add ingredients so that
they don’t get chopped up by the Mixing Paddle

and blended into your loaf. If you are using the
TIMER to delay baking (perhaps while you are asleep
or away from home), you may bypass this function
by ignoring the signal and adding ingredients in the
order called for in the recipe, however, you may end
up with somewhat broken pieces.

To add ingredients, raise the lid and carefully
pour the ingredients into the Baking Pan.

CAUTION: It is important to avoid spilling
ingredients into the oven chamber.

Setting The Timer

(For Delayed Completion)

Use the TIMER when you would like to delay the
completion of your bread or dough. This feature
allows you to delay bake time for up to 13 hours.
For example, it lets you set the TIMER at 7 p.m. one
evening so that you can wake to fresh bread by 8
a.m. the following morning.

NOTE:

The TIMER

cannot be used with the Super Rapid Bake setting.

To set the TIMER, follow these instructions:

NOTE:

Be sure you have followed the “How to Use

Your Breadmaker”

steps 1-6

in preparing the

ingredients in the Baking Pan and selected a MENU.
It is not recommended that you use the “Delayed
Completion” function and TIMER with recipes that
call for fresh ingredients that might spoil such as eggs,
fresh milk, buttermilk, or cheese.

To use the TIMER, you must first set the digital
clock to the correct time of day. To change the

flashing 12:00 a.m., first press the CLOCK button.

While the “Hour”is flashing, immediately

press the

“Up” and “Down” arrows to change the time in 1 hour
intervals. Make sure the “a.m.” or “p.m.” displayed is
appropriate.

While the correct hour is flashing

in the

display, press the CLOCK button again to set the min-
utes. If the hour display has stopped flashing before
the minutes have been set, press the CLOCK button
twice.

While the “00”is flashing,

the minutes can be

set by pressing the “Up” and “Down” arrows. You may
hold either arrow to rapidly change the time in
5-minute intervals, or press and release to change
1 minute at a time.

Once the clock is set,

the TIMER can easily be set

following similar steps. To wake up to the aroma

of fresh baked bread at 8:30 a.m. for example, press
and hold the TIMER button until appears
on the display, and the hour flashes as it did when
setting the clock above.

While the “hour”is flashing,

press the “Up” or “Down” arrows to reach “8”, check-
ing to make sure “a.m.” is displayed. To set the min-
utes, press the TIMER button

while the hour setting

is flashing.

If the hour setting has stopped flashing

How To Use Your Breadmaker

When to add

Time Displayed

Setting

Ingredients after

when Beeper

Signals