Black & Decker BCD7122, Original Instructions Manual

5

ENGLISH

(Original instructions)

the battery pack or tool outside the temperature range 

specified in the instructions. Charging improperly or at 

temperatures outside the specified range may damage 

the battery and increase the risk of fire.

6.  Service

a. 

Have your power tool serviced by a qualified repair 

person using only identical replacement parts. This will 

ensure that the safety of the power tool is maintained.

b. 

Never service damaged battery packs. Service 

of battery packs should only be performed by the 

manufacturer or authorized service providers (only used 

for battery tools).

Drill safety warnings

Safety Instructions for All Operations

‹

Wear ear protectors when impact drilling. Exposure to 

noise can cause hearing loss.

‹

Hold power tool by insulated gripping surfaces, when 

performing an operation where the cutting accessory 

or the fastener may contact hidden wiring. Cutting ac-

cessory or the fastener contacting a “live” wire may make 

exposed metal parts of the power tool “live” and could give 

the operator an electric shock.

‹

Brace the tool properly before use. This tool produces 

a high output torque and without properly bracing the tool 

during operation, loss of control may occur resulting in 

personal injury.

Safety Instructions When Using Long Drill Bits

‹

Never operate at higher speed than the maximum 

speed rating of the drill bit. At higher speeds, the bit is 

likely to bend if allowed to rotate freely without contacting 

the workpiece, resulting in personal injury.

‹

Always start drilling at low speed and with the bit tip 

in contact with the workpiece. At higher speeds, the bit 

is likely to bend if allowed to rotate freely without contact-

ing the workpiece, resulting in personal injury.

‹

Apply pressure only in direct line with the bit and do 

not apply excessive pressure. Bits can bend causing 

breakage or loss of control, resulting in personal injury.

Additional Safety Warnings for Drill/ Driver/ 

Hammerdrill

‹

Use clamps or other practical way to secure and 

support the workpiece to a stable platform. Holding the 

work by hand or against your body is unstable and may 

lead to loss of control.

‹

Accessories and tool may get hot during operation. 

Wear gloves when handling them if performing heat 

producing applications such as drilling metals.

‹

Air vents often cover moving parts and should be avoided. 

Loose clothes, jewelry or long hair can be caught in mov-

d. 

Store idle power tools out of the reach of children and 

do not allow persons unfamiliar with the power tool or 

these instructions to operate the power tool. Power 

tools are dangerous in the hands of untrained users.

e. 

Maintain power tools. Check for misalignment or 

binding of moving parts, breakage of parts and any 

other condition that may affect the power tools 

operation. If damaged, have the power tool repaired 

before use.

 Many accidents are caused by poorly 

maintained power tools.

f. 

Keep cutting tools sharp and clean. Properly 

maintained cutting tools with sharp cutting edges are less 

likely to bind and are easier to control.

g. 

Use the power tool, accessories and tool bits etc. in 

accordance with these instructions, taking into 

account the working conditions and the work to be 

performed. Use of the power tool for operations different 

from those intended could result in a hazardous situation.

h.  Keep handles and grasping surfaces dry, clean and 

free from oil and grease. Slippery handles and grasping 

surfaces do not allow for safe handling and control of the 

tool in unexpected situations.

5.  Battery tool use and care

a. 

Recharge only with the charger specified by the 

manufacturer. A charger that is suitable for one type of  

battery pack may create a risk of fire when used with 

another battery pack.

b. 

Use power tools only with specifically designated 

battery packs.

 Use of any other battery packs may create 

a risk of injury and fire.

c. 

When battery pack is not in use, keep it away from 

other metal objects, like paper clips, coins, keys, 

nails, screws, or other small metal objects, that can 

make a connection from one terminal to another. 

Shorting the battery terminals together may cause burns 

or a fire.

d. 

Under abusive conditions, liquid may be ejected from 

the battery; avoid contact. If contact accidentally 

occurs, flush with water. If liquid contacts eyes, 

additionally seek medical help. Liquid ejected from the 

battery may cause irritation or burns.

e. 

Do not use a battery pack or tool that is damaged or 

modified. Damaged or modified batteries may exhibit 

unpredictable behaviour resulting in fire, explosion or risk 

of injury.

f. 

Do not expose a battery pack or tool to fire or 

excessive temperature. Exposure to fire or temperature 

above 130 °C may cause explosion. NOTE: The 

temperature „130 °C“ can be replaced by the temperature 

"265 °F".

g. 

Follow all charging instructions and do not charge