Black & Decker BDCD12BC, Instruction Manual

3

English

Safety Instructions for All Operations

• 

Hold the power tool by insulated gripping surfaces 

when performing an operation where the cutting 

accessory or fasteners may contact hidden wiring.

Cutting accessory or fasteners contacting a “live” wire may 

make exposed metal parts of the power tool “live” and 
could give the operator an electric shock.

Additional Safety Warnings for Drills

• 

Hold tool firmly with two hands, one hand on the 

handle, and the other gripping the bottom around 

the battery area or the auxiliary handle if provided. 

Loss of control can cause personal injury.

• 

Use clamps or another practical way to secure and 

support the workpiece to a stable platform. 

Holding 

the work by hand or against your body leaves it unstable 

and may lead to loss of control.

• 

Wear safety goggles or other eye protection. 

Hammering and drilling operations cause chips to 

fly.

 Flying particles can cause permanent eye damage.

• 

Do not operate this tool for long periods of time. 

Vibration caused by tool action may be harmful 

to your hands and arms. 

Use gloves to provide extra 

cushion and limit exposure by taking frequent rest periods.

• 

Drill bits may get hot during operation. 

Wear gloves 

when touching them.

WARNING:

 Shock hazard. When drilling or driving 

into walls, floors or wherever live electrical wires may 

be encountered, DO NOT TOUCH ANY METAL PARTS OF 

THE TOOL! Hold the tool only by the plastic handle(s) / 

housing to prevent shock. 

•  Hold drill firmly with both hands to control the 

twisting action of the drill. 

If your drill is equipped with 

a side handle, always use the side handle.

WARNING:

 Drill may stall (if overloaded or improperly 

used) causing a twist. Always expect the stall. Grip the 

drill firmly to control the twisting action and prevent 

loss of control which could cause personal injury. If a 

stall does occur, release the trigger immediately and 

determine the reason for the stall before re-starting.

• 

Always remove the battery pack when attaching or 

removing accessories.

 When attaching accessories in 

the drill chuck, it is important to securely tighten the chuck 
using all three holes to prevent slippage. When using a 
keyless chuck, hand tighten firmly.

Safety Instructions When Using Long 

Drill Bits

• 

Never operate at higher speed than the maximum 

speed rating of the drill bit.

 At higher speeds, the bit is 

likely to bend if allowed to rotate freely without contacting 

the workpiece, resulting in personal injury.

• 

Always start drilling at low speed and with the bit 

tip in contact with the workpiece.

 At higher speeds, 

the bit is likely to bend if allowed to rotate freely without 

contacting the workpiece, resulting in personal injury.

• 

Apply pressure only in direct line with the bit and do 

not apply excessive pressure.

 Bits can bend causing 

breakage or loss of control, resulting in personal injury.

breakage of parts and any other condition 

that may affect the power tool’s operation. If 

damaged, have the power tool repaired before 

use. 

Many accidents are caused by poorly maintained 

power tools.

f ) 

Keep cutting tools sharp and clean. 

Properly 

maintained cutting tools with sharp cutting edges are 

less likely to bind and are easier to control.

g ) 

Use the power tool, accessories and tool bits etc. 

in accordance with these instructions, taking 

into account the working conditions and the 

work to be performed. 

Use of the power tool for 

operations different from those intended could result in 

a hazardous situation.

h ) 

Keep handles and grasping surfaces dry, clean 

and free from oil and grease.

 Slippery handles and 

grasping surfaces do not allow for safe handling and 

control of the tool in unexpected situations.

5) Battery Tool Use and Care

a ) 

Recharge only with the charger specified by the 

manufacturer.

 A charger that is suitable for one type 

of battery pack may create a risk of fire when used with 

another battery pack.

b ) 

Use power tools only with specifically designated 

battery packs.

 Use of any other battery packs may 

create a risk of injury and fire.

c ) 

When battery pack is not in use, keep it away 

from other metal objects, like paper clips, coins, 

keys, nails, screws or other small metal objects, 

that can make a connection from one terminal to 

another.

 Shorting the battery terminals together may 

cause burns or a fire.

d ) 

Under abusive conditions, liquid may be ejected 

from the battery; avoid contact. If contact 

accidentally occurs, flush with water. If liquid 

contacts eyes, additionally seek medical help.

Liquid ejected from the battery may cause irritation 

or burns.

e ) 

Do not use a battery pack or tool that is damaged 

or modified.

 Damaged or modified batteries may 

exhibit unpredictable behavior resulting in fire, 

explosion or risk of injury.

f ) 

Do not expose a battery pack or tool to 

fire or excessive temperature.

 Exposure to 

fire or temperature above 265 °F (130 °C) may 

cause explosion.

g ) 

Follow all charging instructions and do not 

charge the battery pack or tool outside the 

temperature range specified in the instructions. 

Charging improperly or at temperatures outside the 

specified range may damage the battery and increase 

the risk of fire. 

6) Service

a ) 

Have your power tool serviced by a qualified 

repair person using only identical replacement 

parts.

This will ensure that the safety of the power tool 

is maintained.

b ) 

Never service damaged battery packs. 

Service 

of battery packs should only be performed by the 
manufacturer or authorized service providers.