background image

3

ENGLISH

(Original instructions)

Intended use

Your Black & Decker screwdriver has been 

designed for screwdriving applications. This 

tool is intended for consumer use only.

Safety instructions

General power tool safety warnings

@

Warning! Read all safety 

warnings and all instructions. 

Failure to follow the warnings 

and instructions listed below 

may result in electric shock, 

fire and/or serious injury.

Save all warnings and instructions for 

future reference. The term "power tool" in 

all of the warnings listed below refers to your 

mains operated (corded) power tool or battery 

operated (cordless) power tool.

1.  Work area safety

a.  Keep work area clean and well lit. 

Cluttered or dark areas invite accidents.

b.  Do not operate power tools in 

explosive atmospheres, such as in the 

presence of flammable liquids, gases 

or dust. Power tools create sparks which 

may ignite the dust or fumes.

c.  Keep children and bystanders away 

while operating a power tool. 

Distractions can cause you to lose control.

2.  Electrical safety

a.  Power tool plugs must match the 

outlet. Never modify the plug in any 

way. Do not use any adapter plugs with 

earthed (grounded) power tools. 

Unmodified plugs and matching outlets 

will reduce risk of electric shock.

b.  Avoid body contact with earthed or 

grounded surfaces such as pipes, 

radiators, ranges and refrigerators. 

There is an increased risk of electric 

shock if your body is earthed or grounded.

c.  Do not expose power tools to rain or 

wet conditions. Water entering a power 

tool will increase the risk of electric shock.

d.  Do not abuse the cord. Never use the 

cord for carrying, pulling or unplugging 

the power tool. Keep cord away from 

heat, oil, sharp edges or moving parts. 

Damaged or entangled cords increase the 

risk of electric shock.

e.  When operating a power tool outdoors, 

use an extension cord suitable for 

outdoor use. Use of a cord suitable for 

outdoor use reduces the risk of electric 

shock.

f.  If operating a power tool in a damp 

location is unavoidable, use a residual 

current device (RCD) protected supply. 

Use of an RCD reduces the risk of electric 

shock.

Summary of Contents for BDCS361

















Reviews: