background image

WARNING: Read and understand all 

instructions.

Failure to follow all

instructions listed below may result in
electric shock, fire and/or serious personal
injury.

SAVE THESE INSTRUCTIONS

Safety Instructions

DANGER: Laser Radiation, avoid

direct eye exposure, serious eye injury
can result.

• Do not use optical tools such as a
telescope or transit to view the laser 
beam. 
• Position the laser so unintentional eye
contact will be avoided.
• Do not operate the laser around
children or allow children to operate the
laser. 
• Do not disassemble. Modifying the
product in any way can increase the
risk of laser radiation.

WARNING:

Use of controls or

adjustments or performance of
procedures other than those specified in
this manual may result in hazardous laser
radiation exposure.

• Do not operate in explosive atmospheres,

such as in the presence of flammable
liquids, gases, or dust.

• Use only with the specifically designated

batteries. Use of any other batteries may
create a risk of fire.

• Store idle product out of reach of children

and other untrained persons. Lasers are
dangerous in the hands of untrained
users.

• Use only accessories that are

recommended by the manufacturer for
your model. Accessories that may be
suitable for one laser, may create a risk of
injury when used on another laser.

• Repairs and servicing MUST be

performed by a qualified repair facility.
Repairs performed by unqualified
personnel could result in serious injury.

• Do not remove or deface warning labels.

Removing labels increases the risk of
exposure to radiation.

• For indoor use only.
• This product is intended for use in a

temperature range of 41°F(5°C) -

104°F(40°C).

CAUTION:

Use caution when drilling,

nailing or cutting into walls, floors and

ceilings which may contain electrical

wiring or pipes. 

Always turn off the

power when working near electrical
wires.

CAUTION:

Use of controls or

adjustments or performance of procedures

other than those specified in this manual

may result in hazardous laser radiation

exposure.
The label on your tool may include the
following symbols.

V ................................volts
mW ............................milliwatts
nm..............................wavelength in

nanometers

IIIa..............................Class IIIa Laser

For your convenience and safety, the
following labels are on your laser.

2

1

2

w w w . e k t

2

. c o m

Summary of Contents for BDL31 OS






Reviews: