background image

3

2

INSTRUCTION MANUAL

INTENDED USE 

Your Black & Decker power inverter is designed to 

convert direct current (dc) to alternating current 

(AC). It allows the 12V dc current in an automobile to 

supply ac power to operate equipment that is normally 

supplied from a mains power source. This product is 

intended for household, consumer use only. 

SAFETY INSTRUCTIONS

Warning!

 When using battery-powered appliances, 

basic safety precautions, including the following, 

should always be followed to reduce the risk of fire, 

leaking batteries, personal injury and material damage.

• 

Read all of this manual carefully before using the 

appliance.

• 

The intended use is described in this manual. 

The use of any accessory or attachment or the 

performance of any operation with this appliance 

other than those recommended in this instruction 

manual may present a risk of personal injury.

• 

Retain this manual for future reference.

Using your inverter

Always take care when using the inverter. 

• 

For indoor or in-car use only.

• 

This appliance is not intended for use by persons 

(including children) with reduced physical, sensory 

or mental capabilities, or lack of experience and 

knowledge, unless they have been given supervision 

or instruction concerning use of the appliance by a 

person responsible for their safety.

• 

Children should be supervised to ensure that they do 

not play with the appliance.

• 

Use in a dry location only. Do not allow the appliance 

to become wet. Do not immerse the appliance in water.

• 

Do not open body casing. There are no user-

serviceable parts inside.

• 

Do not operate the appliance in explosive 

atmospheres, such as in the presence of flammable 

liquids, gases or dust.

• 

To reduce the risk of damage to plugs and cords 

never pull the cable to remove the plug from a 

socket.

After use

• 

When not in use, the appliance should be stored in a 

dry, well ventilated place out of the reach of children.

• 

Children should not have access to stored appliances. 

• 

When the appliance is stored or transported in a 

vehicle it should be placed in the boot or restrained 

to prevent movement following sudden changes in 

speed or direction.

• 

The appliance should be protected from direct 

sunlight, heat and moisture.

Inspection and repairs

• 

Before use, check the appliance for damaged or 

defective parts. Check for breakage of parts, damage 

to switches and any other conditions that may affect 

its operation.

• 

Do not use the appliance if any part is damaged or 

defective.

• 

Have any damaged or defective parts repaired or 

replaced by manufacturer.

• 

Never attempt to remove or replace any parts other 

than those specified in this manual.

Specific safety instructions for power 

inverters

Warning!

 This appliance converts power from a 12V 

dc battery to mains supply voltage. Take precautions, 

including the following, to avoid the risk of electric 

shock.

• 

Only connect a plug fitted to the supply cord of an 

appliance to the inverter.

• 

Never connect an appliance by modifying the plug or 

by using an adapter unless otherwise instructed by 

this instruction manual.

• 

The length of an appliance power cord to the inverter 

must not exceed two metres unless otherwise 

instructed by this instruction manual.

• 

Never connect an appliance that is damaged or 

incomplete.

• 

Never connect the inverter to the mains supply or to 

the output of another inverter.

 

– The inverter cannot convert the mains supply 

to dc voltage.

 

– The inverter cannot be used to supplement 

the mains supply.

• 

Disconnect the 12V dc accessory plug from the 

power source and remove the appliance plug from 

the inverter before performing any maintenance or 

before cleaning the appliance. 

• 

Do not cover the inverter. Only use in well ventilated 

areas.

• 

Do not open the inverter, there are no serviceable 

parts inside. Do not probe the inverter.

• 

Check that connections to the dc supply are clean 

and secure. Loose connectors may cause overheated 

wires and melted insulation.

• 

Check to make sure you have not reversed the polarity.

• 

Do not install in engine compartments.

• 

Do not use the inverter to supply any medical devices.

Warning! 

A reverse polarity connection will result in a 

blown fuse and may cause permanent damage to the 

power inverter. Damage due to reversed polarity is not 

covered by the warranty.

Warning!

 Do not use with positive ground electrical 

systems, (i.e. older vehicles).

2

4

7

6

3

1

9

5

8

BDPC400AU_Manual_091216.indd   2-3

9/12/2016   11:55:46 AM

Summary of Contents for BDPC400AU

Page 1: ...8331 4800 Email service directed com au Baccus Worldwide LLC Weena 290 3012 NJ Rotterdam or Postbus 819 3000 AV Rotterdam 31 0 10 282 16 11 Cat BDPC400AU September 2016 RD091216 Printed in China 500WATT POWER INVERTER WITH USB CHARGING PORT INSTRUCTION MANUAL BDPC400AU_Manual_091216 indd 8 1 9 12 2016 11 55 45 AM ...

Page 2: ...anges in speed or direction The appliance should be protected from direct sunlight heat and moisture Inspection and repairs Before use check the appliance for damaged or defective parts Check for breakage of parts damage to switches and any other conditions that may affect its operation Do not use the appliance if any part is damaged or defective Have any damaged or defective parts repaired or rep...

Page 3: ...utputs up to 100 Watts only The tip of the plug is positive and the side contact is negative Warning Make sure that the On Off button is turned off 0 and that no flammable fumes are present in the installation area before connecting the accessory plug to the accessory outlet Warning Connect the ring terminals to the terminals of the power inverter before connecting the accessory plug to the access...

Page 4: ... If the inverter on off switch has been pressed to turn the unit on but there is no mains or USB power output and the power fault LED flashes then one of the following conditions has occurred Low battery voltage Over voltage Short circuit Overload Over temperature Press the on off switch to turn the inverter off correct the fault and then press the on off switch again to turn the inverter back on ...

Reviews: