5
ENGLISH
◆
Slide the unit onto de rails.
Use
◆
Place the appliance on a flat surface.
◆
Ensure the appliance is dry before stepping onto it.
Setting personal data (fig. C & D)
The memory can store personal data for up to 12 persons.
◆
Switch the appliance on.
◆
Wait for the message (10) to appear blinking on the
screen (4).
◆
Select a program number by pressing the adjustment
buttons (2).
◆
Confirm the selection by pressing the set button (3).
◆
Enter the data in the menus appearing in the order as
follows.
Selecting the measurement system
The appliance can show the results both in the metric (11) and
the imperial (12) system.
◆
Enter the measurement system by pressing the buttons (2)
as required.
◆
Store the data by pressing the set button (3).
Selecting the gender
The screen will display the gender by a female (13) or a male (14)
symbol.
◆
Enter the gender by pressing the buttons (2) as required.
◆
Store the data by pressing the set button (3).
Setting the height
The screen will show the data in in centimeters (15).
◆
Enter the height by pressing the buttons (2) as required.
◆
Store the data by pressing the set button (3).
Setting the age
The screen will show the data in years of age (16). The screen
will display the child mode symbol (17) if the selected age is 12
or below.
◆
Enter the age by pressing the buttons (2) as required.
◆
Store the data by pressing the set button (3).
Storing the data
After the program number has stopped blinking and remains
on, the data has been stored in the memory.
◆
If necessary, select a following program number and
repeat the steps to enter the data for the next person.
Switching on and off
Switching on
◆
Press the on/off button (1) on the remote control.
When the remote control is fitted, the appliance is
activated automatically. When the remote control is
removed, the appliance must be activated by tapping the
centre of the scale with one foot.
Auto switch-off
◆
After approximately 10 seconds of inactivity, the screen
will go blank.
Measuring the weight (fig. C)
◆
Switch the appliance on by pressing the on/off button (1)
twice. The message (19) appears on the screen (4).
◆
Tap the centre of the scale with one foot to activate the
appliance. The message (20) appears on the screen (1).
◆
Step on the appliance. The digits on the screen start blinking.
◆
The result appears on the screen.
Measuring the body fat and water percentage
(fig. C, D & E)
These measurements are an indication of your level of fitness
and your physical health. Consult your physician or a qualified
dietician for appropriate advice regarding further action.
The measurements are performed using the technique of BIA,
a highly reliable method for analyzing the composition of the
human body. BIA, short for bioelectrical impedance analysis,
measures the resistance to the flow of a small, harmless
low-level electrical current using the built-in electrodes.
Personal data like gender, height and age, form the key factors
to the analysis results processed by the software program.
When using this application, we recommend that you take
regular measurements, always around the same time of day
and under the same conditions.
Refer to the tables below for an indicative interpretation of
the analysis results.
Note:
– The application only works if you are barefoot.
– Excessive drinking or eating, exercising, medical
conditions, use of medication, the female menstrual cycle
etc., have an effect on the measurement results.
–
Warning!
This application must not be used by pregnant
women and people with a cardiac pacemaker or any other
medical device implanted in their body.
◆
Remove the remote control from the appliance.
◆
Switch the unit on.
◆
Wait for the message (10) to appear blinking on the
screen (4).
◆
Select the program number of your personal data.
