Black & Decker FSMH1321, User Manual

8

ENGLISH

(Original instructions)

9

ENGLISH

(Original instructions)

Attachin

g the hand held steam cleaner (Fig. B)

u

  Holding the back of the steam mop body (11) push the 

hand held steam cleaner (5) firmly into the steam mop 

body (11) making sure it sits correctly over the interface 

(11a) and clicks securely into place.

Removing

 the hand held steam cleaner (Fig. B)

u

  Push the release button (10) on the main body (11) and lift 

the hand held steam cleaner (5) off the interface (11a) and 

away from the main body (11).

Attaching a cleaning pad (Fig. C)

Replacement cleaning pads are available from your 

BLACK+DECKER dealer :- (cat  no. 

FSMP20-XJ

).

u

  Place a cleaning pad (13) on the floor with the velcro 'loop' 

side facing up.

u

  Lightly press the steam mop down onto the cleaning pad 

(13).

Note: 

This unit may be supplied with a standard floor cleaning 

head (12) or a steam burst cleaning head (12a). In either case 

use these instructions to fit a cleaning pad.

Caution! 

Never leave the steam mop in one spot on any 

surface for any period of time. Always place the steam mop 

with the handle (8) supported in the upright position when 

stationary and make sure the steam mop is turned off when 

not in use.

Removing a cleaning pad

Caution!

 Always wear suitable shoes when changing the 

cleaning pad on your steam mop.  

Do not wear slippers or open toed footwear.

u

  Return the handle (8) to the upright position and turn the 

steam mop 'OFF'.

u

  Wait until the steam mop cools down (approximately 5 

minutes).

u

  Lift the steam mop away from the cleaning pad freeing it 

from the velcro fastening.

Caution! 

Never leave the steam mop in one spot on any 

surface for any period of time.  

Always place the steam mop with the handle (8) supported in 

the upright position when stationary and make sure the steam 

mop is turned off when not in use.

Filling the water tank (Fig. Q)

Note! 

Fill the water tank with clean tap water (Do not use any 

additives or chemicals).

Note! 

In areas of hard water, the use of de-ionised water is 

recommended.

u

  Open the filler cap (4) by flipping it up.

u

  Fill the water tank with water (Do not use any additives or 

chemicals).

Warning!

 When filling, detach from main unit and maintain in 

a horizontal position.

Warning! 

Your water tank has a 0.5 litre capacity. Do not over 

fill the tank.

u

  Close the filler cap (4).

Note! 

Ensure the filler cap is firmly secured.

A

ttaching the carpet glider (12b) (For use on 

carpets only)

u

  Place the carpet glider (12b) on the floor.

u

  Attach a cleaning pad to the floor cleaning head (12)

u

  Lightly press the steam mop down onto the carpet glider 

(12b) until it clicks into place.

Caution! 

Never leave the steam mop in one spot on any 

surface for any period of time. Always place the steam mop 

with the handle (8) supported in the upright position when 

stationary and make sure the steam mop is turned off when 

not in use.

Removing

 the carpet glider

Caution! 

Always wear suitable shoes when changing the 

carpet glider on your steam mop. Do not wear slippers or 

open toed footwear.

u

Return the handle (8) to the upright position and turn the 

steam mop 'OFF'.

u

  Wait until the steam mop cools down (approximately 5 

minutes).

u

  Place the front of your shoe onto the carpet glider removal 

tab and press down firmly.

u

  Lift the steam mop up and off the carpet glider.

Caution! 

Never leave the steam mop in one spot on any 

surface for any period of time. Always place the steam mop 

with the handle (8) supported in the upright position when 

stationary and make sure the steam mop is turned off when 

not in use.

Attaching the hose and accessories to the 

hand held steam cleaner (Fig. G - O)

Warning! 

Inspect the seal between the connection point on 

the hand held steam cleaner (5) and the steam hose (16) 

before each use. If the seal malfunctions or is damaged, 

please contact your nearest authorised repair agent. Do not 

use the appliance. 

Attaching the hose

u

Press the steam hose release button (16a) on the steam 

hose (16).

u

Connect the steam hose (16) to the hand held steam 

cleaner (5) and release the steam hose release button 

(16a) making sure it clicks into place.

Important! 

Ensure that the steam hose (16) is securely 

connected to the hand held steam cleaner (5). If steam 

escapes from the joint, the hose is incorrectly fitted. Switch off, 

allow the unit to cool then remove and refit the hose.