6
ENGLISH
(Original instructions)
7
ENGLISH
(Original instructions)
u
Press the steam operate button (2). After a few seconds,
steam will start to come out of the steam head.
Note!
When first filled or after running dry, it can take up to 45
seconds for steam to be produced.
u
It takes a few seconds for steam to enter the cleaning pad.
The steam mop will now glide easily over the surface to be
sanitized/cleaned.
u
Push and pull the steam mop slowly across the surface to
thoroughly steam clean each section.
u
When you have finished using the steam mop, return
the handle (9) to the upright position, making sure that it
is supported and turn it 'OFF'. Wait until the steam mop
cools down (approximately five minutes).
Caution!
It is important to monitor the water level in the water
tank (4). To refill the water tank and continue to sanitize/
clean stand the mop upright making sure that the handle is
supported and turn the steam mop 'OFF'. Unplug the unit from
the electrical wall outlet, refill the water tank (4).
Caution!
Never leave the steam mop in one spot on any
surface for any period of time. Always place the steam mop
with the handle (9) supported in the upright position when
stationary and make sure the steam mop is turned off when
not in use.
After use (Fig. H)
u
Turn the steam mop 'OFF'. turn the steam operation
button (2) to off and then press the ON/OFF button (1).
u
Wait until the steam mop cools down.
u
Unplug the steam mop from the electrical wall outlet.
u
Empty the water tank.
u
remove the cleaning pad (7) and wash it ready for next
use.
u
Wrap the power supply cable around the tidy hook (10).
Technical Data
FSMH13E5
FSMH13E10
Voltage
V
ac
220-240
220-240
Power
W
1300
1300
Tank
Capacity
ml
380
380
Weight
kg
1.8
1.8
Troubleshooting
If your appliance seems not to operate properly, follow the
instructions below. If this does not solve the problem, please
contact your local BLACK+DECKER repair agent.
Problem
Step
Possible solution
The steam mop is not
turning on
1.
Check the unit is plugged in at the
wall socket.
2.
Check the unit is switched on using
the ON/OFF switch (1)
3.
Check the fuse in the plug.
The steam mop is not
producing steam
4.
Check the water tank (4) is full .
NOTE:
When first filled or after
running dry it can take up to 45
seconds for steam to be produced.
5.
Check the steam generation button is
in the ON position (2).
6.
The steamer is equipped with a
thermostat and a thermal cut-out. If
for any reason the steamer overheats
it will switch off. If this happens turn
off and unplug the steamer, allow to
cool for 2 to 4 hours and re-try.
Where can I get further
information/
accessories for my
steam mop
7.
Refer to the assembly chapter of the
manual for correct fitting of parts and
accessories.
Maintenance and cleaning
Your BLACK+DECKER corded appliance has been designed
to operate over a long period of time with a minimum of main-
tenance. Continuous satisfactory operation depends upon
proper appliance care and regular cleaning.
Warning!
Before performing any maintenance or cleaning on
corded appliances switch off and unplug the appliance.
u
Wipe your appliance over using a soft damp cloth.
u
For stubborn marks you can use a mild solution of soap and
water to dampen your cloth.
Care of the cleaning pads
Wash care instructions -
No fabric conditioner - Allow to dry
fully before re-use.
Caution!
Follow the cleaning instructions printed on the label
of the cleaning pad.
Protecting the environment
Z
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Should you find one day that your Black & Decker product
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product
available for separate collection
.
z
Separate collection of used products and packag-
ing allows materials to be recycled and used again.
Re-use of recycled materials helps prevent enviro
mental pollution and reduces the demand for raw
materials.
