ENGLISH
18
This Instruction Manual provides important installation, use,
maintenance and safety information and must be at hand at all
times. Before operating this equipment, read this manual and make
sure you understand all of its instructions in order to avoid personal
injuries or damage to your piston compressor.
SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
If an Air Compressor is improperly used it may cause
physical and material harm. In order to avoid them, follow
the recommendations below:
1.
This equipment:
-
has hot, electric and moving parts;
-
when connected to electric power, it may turn on or turn off
automatically due to tank’s pressure or to the tripping of
electric protectionelements;
-
may cause mechanical or electric interferences in nearby
equipment;
-
must not work in places where non authorized people,
children or animals may have access;
-
requires an authorized person to supervise its use and
maintenance as well as the use of adequate individual
protection equipment;
-
must be installed and operated in well ventilated areas and
protected against humidity or water leakage.
2.
Never exceed the maximum pressure indicated in the compressor’s
identification tag/sticker.
3.
Do not change the pressure switch safety valve factory adjustment. If
any adjustment to the pressure switch is needed, call the nearest
Black&Decker
Authorized Service Center.
4.
Never weld or carry out maintenance jobs on the tank, once
they may affect its resistance or may hide more serious
problems. In case of leakage, cracks or deterioration caused
by corrosion, stop using the equipment immediately and get
in touch with the nearest
Black&Decker
Authorized Service
Center.
5.
Never run the tank above the maximum pressure indicated on its
identification tag.
6. The end user must provide a new inspection of the Pressure
Vessel (tank) to be carried out after 5 (five) years from the
manufacturing date shown in its identification tag, or when
there is chemical or mechanical damage that may endanger its
resistance. The inspection must be carried out and approved by
a duly qualified engineer (skilled professional), according to
local technical standards and legislation. The next period for
testing will be determined by the responsible engineer himself.
We recommend that the Pressure Vessel (tank) be exchanged
for a new one every 10 (ten) years, or according to the
responsible engineer’s judgment.
7.
Air compression is a heat generating process and parts and
accessories are subject to high temperatures. Therefore,
one must be careful when handling them in order to avoid
burns.
8.
The produced compressed air is not adequate for
human consumption. To use it for this purpose, it is
necessary to install special filters. Please contact
Black&Decker for aditional information.
9.
Do not carry out any maintenance while the compressor is
on. Do not clean or touch the electric components without
unplugging the compressor from the outlet.
10.
The refrigeration air intake protecting screen must be always clean
to prevent the propeller from pulling in impurities.
11.
Never clean the compressor’s external surface with solvent
(thinner). Always use neutral detergent.
12.
Avoid the accumulation of solvents, paints or other
chemicals that may cause damage or explosion risk to the
compressor.
13.
Always use an electric extension cord according to
specifications (see Table 2 - page 23) which must not be
amended. If these recommendations are not followed, the
user may be injured and the compressor’s electric
components may be damaged, violating the warranty.
When necessary, use a longer air hose.
14.
If the equipment presents any irregularities, stop its use immediately
and call the nearest
Black&Decker
Authorized Service Center.
IMPORTANT
ATTENTION
WELCOME
INTRODUCTION
COMPRESSOR INSPECTION
You have purchased another product with
Black&Decker
quality
standards.
The design, inspection and manufacturing of your
Black&Decker
tank
is based on EN286-1 1998 Attachment 1 - Code and according to NR-13
MTb of Brazil.
It is a mix of high technology and easy use.
WE RECOMMEND READING THIS MANUAL PRIOR TO
USING THIS PRODUCT.
It will help you to optimize product performance, guarantee safe use and
guide you in preventive maintenance.
If there is any problem that cannot be solved by the information provided in
this manual, please contact the nearest
Authorized
Service Center.
In order to extend the useful life of this coaxial air compressor, the use of
mineral lubricant oil and original parts are highly recommended.
The pressure vessel quality certificate must be presented to authorities, in
case of inspection. Keep it in a safe place along with the instruction
manual.
Black&Decker
Inspect for signs of obvious or concealed freight damage. Report any
damage to the delivering freight carrier immediately. Be sure that all
damaged parts are replaced and any mechanical problems are corrected
prior to the operation of the air compressor. The air compressor serial
number is located on the pump or tank. Please write the serial number in
the space provided in the service section for future reference.
When using electric product, basic safety
precautions should always be followed to
reduce risk of fire, electric shock, and
personal injury.
WARNING
