4
5
dry-cell batteries that are commonly used with home
appliances. These batteries may burst and cause
injury to persons and damage property.
• Check the polarity of the vehicle battery terminals
before connecting the appliance. Always disconnect
the negative (black) jumper cable first: followed by
the positive (red) jumper cable.
• The jump-starter power switch should be in the off
position before connection to a power source or
load, when the unit is charging and when not in use.
• Never allow the red and black clamps to touch each
other or another common metal conductor. This
could cause damage to the appliance and/or create a
sparking/explosion hazard. Always store the battery
clamps in the built-in holders when not in use.
• When using this unit in proximity to the vehicle’s
battery and engine, stand the unit on a flat, stable
surface, and be sure to keep all clamps, cords,
clothing and body parts away from moving parts of
the vehicle.
• This appliance contains a sealed lead-acid battery. It
is recommended that the appliance is laid flat during
storage, use, and recharging.
• Excessive engine cranking can damage a vehicle’s
starter motor. If the engine fails to start after the
recommended number of attempts, discontinue
jump-start procedures and look for other problems
that may need to be corrected.
• Do not use this jump-starter on a watercraft. It is not
qualified for marine applications.
Warning! Burst hazard: Do not use the unit for
charging dry-cell batteries that are commonly used
with home appliances. These batteries may burst
and cause injury to persons and damage property.
Use the unit for charging/boosting a lead-acid battery
only. It is not intended to supply power to a low-
voltage electrical system other than in a starter-motor
application.
Warning! Explosive gas may be vented from lead acid
batteries when charging. The battery must be placed
in a well-ventilated area and you must remove any
sources of ignition when conducting jump starting
procedures.
• To reduce the risk of electric shock, disconnect the
appliance from any power source before attempting
maintenance or cleaning. Turning off controls without
disconnecting the appliance will not reduce this risk.
• Make sure the appliance is disconnected from all
charging power sources before beginning the jump
start procedure.
Additional safety instructions for
batteries and chargers
BATTERIES
• Never attempt to open for any reason.
• Do not expose the battery to water.
• Do not store in locations where the temperature may
exceed 40°C.
• Charge only at ambient temperatures between 4°C
and 40°C.
• Charge only using the chargers provided with the
appliance.
• When disposing of batteries, follow the instructions
given in the section “Protecting the environment”.
• Under extreme conditions, battery leakage may
occur. When you notice liquid on the batteries,
carefully wipe the liquid off using a cloth. Avoid skin
contact.
CHARGERS
The following symbols are found on your mains
charger:
Your charger is double
insulated; therefore no earth
wire is required.
Your charger is a switch mode
power supply unit.
Your charger incorporates
a short-circuit-proof safety
isolating transformer
(inherently or non-inherently)
Indication of correct connection
of your charger.
The charger is intended for
indoor use only.
Your charger meets the Energy
Efficiency Level V standard
for no-load condition electric
power consumption and
average active efficiency of
external power supplies.
Your charger is rated to IP20
degree of protection provided
by the enclosure.
Your charger has been designed for a specific voltage.
Always check that the mains voltage corresponds to
the voltage on the rating plate.
Warning! Never attempt to replace the charger unit
with a regular mains plug.
Use your Black & Decker charger only to charge the
battery in the tool with which it was supplied. Other
batteries could burst, causing personal injury and
damage.
• Never attempt to charge non-rechargeable batteries.
• Have defective cords replaced immediately.
• Do not expose the charger to water.
• Do not open the charger.
• Do not probe the charger.
• The battery must be placed in a well ventilated area
when charging.
Electrical safety
Always check that the power supply corresponds to
the voltage on the rating plate.
• If the supply cord is damaged, it must be replaced
by the manufacturer in order to avoid a hazard.
PERSONAL SAFETY
Always have protective eyewear when using this
product: contact with battery acid may cause
blindness and/or severe burns. Be aware of first aid
procedures in case of accidental contact with battery
acid.
Avoid touching the eyes while working with a battery.
Acid, acid particles or corrosion may get into the eyes.
Have plenty of fresh water and soap nearby in case
battery acid contacts skin.
Remove personal metal items such as rings, bracelets,
necklaces and watches when working with a lead-acid
battery. A lead-acid battery can produce a short circuit
current high enough to cause a severe burn.
Be extra cautious to reduce the risk of dropping a
metal object onto the battery. This might cause sparks
or short-circuit the battery or other electrical part,
which can cause an explosion.
Warning! Battery fluid is a diluted sulphuric acid and
may cause personal injury or damage to property. In
case of skin or eye contact, follow the instructions
below.
• In case of skin contact, immediately rinse with water.
If redness, pain or irritation occurs seek medical
attention.
• In case of eye contact, rinse immediately with clean
water and seek immediate medical attention.
FEATURES
1. 12V dc accessory outlet (under protective cover)
2. Jump-starter power switch
3. Positive (+) red clamp
4. USB power indicator
5. USB power button
6. USB port (under protective cover)
7. Battery status LED indicators
8. Battery power level button
9. Reverse polarity indicator
10. Negative (–) black clamp
11. Rubber grip handle
12. Charging socket
13. Mains charging adapter
CHARGING THE UNIT
This unit is shipped in a partially charged state.
• Charge the unit before first use using the mains
charging adapter for 24 hours.
Lead-acid batteries need to be kept fully charged and
well maintained to ensure they continue to function
properly. All batteries lose energy from self-discharge
over time and more rapidly at higher temperatures.
When the unit is not in use, manufacturer recommend
that the battery is charged at least every 30 days.
• Check the battery charge level by pressing the
battery status button. The battery status LED
indicators will show the level of battery charge.
When only one red LED lights, charge the unit.
• Make sure all other unit functions are turned off
during recharging, as this can slow the recharging
process.
Note:
Charging the battery after each use will prolong the battery
life; frequent heavy discharges between charges and/or
overcharging will reduce battery life.
Important! When the battery is overly discharged and
if the green LED is lit when the charger is plugged in,
this indicates the battery is at a high impedance stage.
In this event, recharge the unit for a period of 24
hours before use.
• Insert the jack of the mains charging adapter into the
charging socket on the back of the unit.
• Insert the mains charging adapter plug into a mains
power socket.
• Charge until the green battery status LED indicator
lights solid or flashes.
• Disconnect the mains charging adapter from the
mains power socket and then remove the plug of
mains charging adapter from the charging socket
on the back of the unit. Press the battery status
button. If all 3 status lights illuminate, the unit is fully
charged. Store the mains charging adapter in a safe
place.
USE
Using the jump-starter
1. Turn off the vehicles ignition and all accessories
before making any connections.
2. Make sure that the jump-starter power switch is
turned off.
3. Check polarity of battery posts. Positive (POS, P,
+) battery post usually has larger diameter than
negative (NEG, N, –) post.
4. Determine which post of the battery is grounded
(connected to the chassis). If negative post is
grounded (as in most vehicles), see 5. If positive
post is grounded, see 6.
5. For negative-grounded vehicle, connect positive
(red) clamp from battery charger to positive
(POS, P, +) ungrounded post of battery. Connect
J312BAU_Manual_091216.indd 4-5
9/12/2016 11:59:48 AM
