background image

11

TROUBLESHOOTING (CON’T.)

Problem

Possible Cause

Possible Solution

• Circuit breaker is tripped.

• Reset circuit breaker. 

(If the product repeatedly 

causes the circuit 

breaker to trip, 

discontinue use 

immediately and have it 

serviced at a Black &

Decker service center or 

authorized servicer.)

• Cord or switch is damaged.

• Have cord or switch 

replaced at Black

& Decker Service 

Center  or Authorized 

Servicer

For assistance with your product, visit our website 

www.blackanddecker.com

for the

location of the service center nearest you or call the BLACK & DECKER help line at 

1-800-544-6986.

Service Information

All Black & Decker Service Centers are staffed with trained personnel to provide

customers with efficient and reliable power tool service. Whether you need technical

advice, repair, or genuine factory replacement parts, contact the Black & Decker location

nearest you. To find your local service location, refer to the yellow page directory under

"Tools—Electric" or call: 

1-800-544-6986

or visit 

www.blackanddecker.com

Full Two-Year Home Use Warranty 

Black & Decker (U.S.) Inc. warrants this product for two years against any defects in

material or workmanship. The defective product will be replaced or repaired at no charge

in either of two ways.
The first, which will result in exchanges only, is to return the product to the retailer from

whom it was purchased (provided that the store is a participating retailer). Returns should

be made within the time period of the retailer’s policy for exchanges (usually 30 to 90

days after the sale). Proof of purchase may be required. Please check with the retailer for

their specific return policy regarding returns that are beyond the time set for exchanges.
The second option is to take or send the product (prepaid) to a Black & Decker owned or

authorized Service Center for repair or replacement at our option. Proof of purchase may

be required. Black & Decker owned and authorized Service Centers are listed under

"Tools-Electric" in the yellow pages of the phone directory and available on our website

www.blackanddecker.com.

This warranty does not apply to accessories. This warranty gives you specific legal rights

and you may have other rights which vary from state to state. Should you have any

questions, contact the manager of your nearest Black & Decker Service Center. This

product is not intended for commercial use.

Free warning label replacement: 

If your warning labels become illegible or are missing,

call 

1-800-544-6986 

for a free replacement.

See ‘Tools-

Electric’

– Yellow Pages –

for Service &

Sales

Black & Decker (U.S.)

Inc., 

701 E. Joppa Rd.

Towson, MD 21286

U.S.A.

Summary of Contents for MS2000












Reviews: