background image

1-800-PFAUCET (1-800-732-8238)

For Toll-Free Pfaucet information call 

1-800-PFAUCET (1-800-732-8238) 

or visit www.pricepfi ster.com

•  Installation Support

•  Care and Warranty Information

CAUTION:  Maintenance

DISASSEMBLY

1. Replacement parts may be available at the store where you 

purchased your faucet.

2. When replacement parts are not available, please write or 

call Price Pfi ster Consumer Service.

3. Always  turn  off  water  and  relieve  pressure  before 

working on your faucet.

NOTE:  Trim Care

Cleaning Instructions:

For all handles and decorative fi nishes, use only a soft damp 

cloth  to  clean  and  shine.  Use  of  polish,  detergents,  abrasive 

cleaners, organic solvents, or acid may cause damage. 

Use of 

other than a soft damp cloth will nullify our warranty!

Special Trim:

  

Trim  products  which  contain  porcelain  or  other  similar 

substances are not acceptable for public areas or commercial 

use. Installation of said trim is at user’s risk!

24   FLUSHING & AERATOR CLEANING

To prevent damage to the internal parts of your faucet from debris that may 

have collected in the water lines, please follow these steps: 

1. Turn on water supply valves. 

2. After connections have been made, remove Aerator (

24A

) and turn Handles 

to the full “ON” position. 

3. Check for leaks, retighten where necessary, and let lines fl ush for one minute 

without moving faucet handles. This will remove debris from lines which 

can damage internal parts of faucet and cause leaks. 

4. After fl ushing, turn off handles and replace Aerator (

24A

). 

To clean aerator, lift out Washer (

24B

) and Insert (

24C

) from Aerator Head 

(

24A

). Rinse parts and replace. 

25   VALVE CARTRIDGE MAINTENANCE

Turn off water supplies and relieve pressure before working on your faucet  

(see step 2)

. Remove Handles (

25A

)  

(see step 16)

, Valve Adapter (

25B

)  

(see step 13)

, unscrew Cartridge Assembly (

25C

) and inspect. Replace parts 

as necessary.

26   HOSE CONNECTION MAINTENANCE

To detach Hose Assembly (

26A

), remove Clips (

26B

) from End Valve (

26C

and unscrew Locknut (

26D

) from Valve Stem (

26E

). Pull the Center Connector 

26E

26E

(

26F

) and End Connectors (

26F

26F

26G

) down until Hose Assembly (

26A

) is free.

Inspect parts and replace as necessary.

MAINTENANCE & CARE

26

24

25

7

ENGLISH

24A

24A

24B

24C

24A

24A

25A

25A

25B

25C

26C

26B

26B

26D

26C

26E

26F

26G

26G

26A

26A

Summary of Contents for Price Pfister Marielle 49M









Reviews: