5
English
READ ALL INSTRUCTIONS
Important Safety Instructions for All
Integral Battery Tools
WARNING:
Read all safety warnings, instructions,
and cautionary markings for the battery, charger
and product. Failure to follow the warnings and
instructions may result in electric shock, fire and/
or serious injury.
•
NEVER force a charger cord plug into the tool.
•
DO NOT modify a charger cord plug in any way to fit
into the tool as the battery may rupture causing serious
personal injury.
•
DO NOT charge or use the battery in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust.
Inserting or removing the USB
cable plug from the tool may ignite the dust or fumes.
•
DO NOT
splash or immerse in water or other liquids.
•
DO NOT
allow water or any liquid to enter tool.
•
DO NOT store or use the tool in locations where the
temperature may reach or exceed 104 °F (40 °C) (such
as outside sheds or metal buildings in summer).
For
best life store tools in a cool, dry location.
NOTE: Do not store the tool with the switch locked on.
Never tape the switch in the ON position.
•
DO NOT incinerate the tool even if it is severely
damaged or is completely worn out.
The battery can
explode in a fire. Toxic fumes and materials are created
when lithium‑ion batteries are burned.
•
If battery contents come into contact with the skin,
immediately wash area with mild soap and water.
If
battery liquid gets into the eye, rinse water over the open
eye for 15 minutes or until irritation ceases. If medical
attention is needed, the battery electrolyte is composed of a
mixture of liquid organic carbonates and lithium salts.
•
Contents of opened battery cells may cause
respiratory irritation.
Provide fresh air. If symptoms
persist, seek medical attention.
BATTERY AND CHARGER
The battery is not fully charged out of the carton. Before using
the charger to charge the battery, read the safety instructions
below and then follow charging procedures outlined.
Ah .......................amp hours
or AC ...........alternating current
or AC/DC .... alternating or direct
current
...................... Class II Construction
(double insulated)
no .......................no load speed
n .........................rated speed
PSI....................... pounds per square
inch
......................earthing terminal
.....................safety alert symbol
..................... visible radiation
do not stare into
the light
..................... wear respiratory
protection
..................... wear eye protection
..................... wear hearing
protection
..................... read all
documentation
..................... do not expose to
rain
The label on your tool may include the following symbols. The
symbols and their definitions are as follows:
V ......................... volts
Hz .......................hertz
min .....................minutes
or DC ......direct current
...................... Class I Construction
(grounded)
…/min ..............per minute
BPM ....................beats per minute
IPM .....................impacts per minute
OPM .................... oscillations per
minute
RPM .................... revolutions per
minute
sfpm ................... surface feet per
minute
SPM ....................strokes per minute
A .........................amperes
W ........................watts
Wh ......................watt hours
WARNING:
Use of this tool can generate and/or
disperse dust, which may cause serious and permanent
respiratory or other injury. Always use NIOSH/OSHA
approved respiratory protection appropriate for
the dust exposure. Direct particles away from face
and body.
WARNING: Always wear proper personal hearing
protection that conforms to ANSI S12.6 (S3.19)
during use.
Under some conditions and duration
of use, noise from this product may contribute to
hearing loss.
cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• lead from lead‑based paints,
• crystalline silica from bricks and cement and other
masonry products, and
• arsenic and chromium from
chemically‑treated lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to filter
out microscopic particles.
•
Wear protective clothing and wash exposed areas
with soap and water.
Allowing dust to get into your
mouth, eyes, or lay on the skin may promote absorption of
harmful chemicals. Direct particles away from face and body.
•
Use the appropriate dust extractor vacuum to remove
the vast majority of static and airborne dust
. Failure
to remove static and airborne dust could contaminate the
working environment or pose an increased health risk to
the operator and those in close proximity.
•
Use clamps or other practical ways to secure and
support the workpiece to a stable platform.
Holding
the work by hand or against your body is unstable and may
lead to loss of control and injury.
•
Air vents often cover moving parts and should be
avoided.
Loose clothes, jewelry or long hair can be caught
in moving parts.
CAUTION: When not in use, place tool on its
side on a stable surface where it will not cause
a tripping or falling hazard.
Some tools with large
battery packs will stand upright on the battery pack
but may be easily knocked over.
Only for use with S010QU1400040 chargers.
