background image

Chapter 5: Operation

877-877-2269   |   blackbox.com 

Page 21

5. Operation

The Central Power Hub system is designed to be transparent in operation. 

5.1 Indicators

The Central Power Hub main chassis contains various indicators to provide you with status information. There are four main indi-
cators on the front panel as well as green and amber indicators on the network port connector.

5.1.1 Red status indicators

The red status indicators on the front panel 
provide various key power and operation 
feedback:

Green

Off:   No link
On:  Network link active

Amber

Off:  

No link

On/flashing: Network link present

P1

On:  The power 
module in bay 1 has 
a mains input and is 
operating.
Flashing:  An invalid 
power module has 
been inserted into 
bay 1.

INVLD

Flashing:  One (or 
both) of the power 
modules is an invalid 
type.

OVLD

On:  An overload condition 
has been detected on one 
or more of the 12V output 
ports. The port will have 
powered down. After 
rectifying the cause, press 
the recessed CLEAR button 
to re-enable the port.

Note: An OVLD condition 
can also be cleared by 
clicking the FAULT indicator 
in the management 
application.

P2

On:  The power 
module in bay 2 has 
a mains input and is 
operating.
Flashing:  An invalid 
power module has 
been inserted into 
bay 2.

Note: The P1 and P2 indicators mimic the 
green indicators that are located on the rear of 
each power module, near to their cooling fans.

On:  Power (12VDC) is being 
supplied to the adjacent port.

5.1.2 Green and amber network status 
indicators

The green and amber status indicators on the front 
panel network port connector provide further status 
information: 

5.1.3 Green power output status 
indicators

On the rear panel, each power output port has 
a green status indicator: 

Summary of Contents for ACR1000-12V5-CBL2M



























Reviews: