background image

16

1

About Media Converters

The modular 

Media Converter Series

includes

modules that convert copper to single-mode,
multi-mode  or single-strand fiber at Ethernet, Fast
Ethernet and Gigabit Ethernet speeds, and mod-
ules that convert copper to thin coax at Ethernet
speeds.  Modules install in a variety of chassis.

Media Converter Chassis

Media  Converter  chassis

provide power to the media conversion modules.  

1-PPort

(LE7401A-R2) chassis include one media conversion module slot.

4-PPort

(LE7404A) chassis include four media conversion module slots.

8-PPort

(LE7408A) chassis is a 1U high rackmountable that includes eight

media conversion module slots. 
The 1, 4 and 8 slot chassis include a fixed 100/240 VAC power supply.

12-PPort

chassis is rackmountable and includes 12 media conversion module

slots and either a 100/240 VAC (LE74012A) or -48 VDC (LE74012A-DC)
power supply.  The 12-Slot chassis is 1U high and has the power on the rear
of the chassis with media conversion module slots on the front. 

10Mbps Media Conversion Modules

10Mbps Media Conversion Modules

provide a single conversion between

10Base-T twisted pair and either 10Base-FL fiber or 10Base-2 coax. Each module
requires one slot in a 

Media Converter

chassis.  The following versions are available:

LE740-TPSTM-R2

TP/FO-MM850-ST

4  Km 

LE740-TPSTM-SC-R2

TP/FO-MM850-SC

4  Km

LE740-TPSTS20-R2

TP/FO-SM1310/PLUS-ST

40 Km

LE740-TPSCS20-R2

TP/FO-SM1310/PLUS-SC

40 Km

LE740-TPBNC

TP/BNC

NOTE: All modules support half- and full-duplex except modules with BNC connectors are always HDX. 

N O T E

This manual will refer to 

all types of modules as “Media

Conversion Modules” except where differences require indi-
catation.

Q U I C K   S T A R T

Introduction

1

Board Diagrams

3

Jumper Settings

4

Crossover/Pass-Through

5

LinkLoss 

&

FiberAlert

6

Auto-Negotiation

8

Installation of Modules

9

LED Operation

11

Technical Support

11

Modular Media Converter 

Installation Guide 

(includes cchassis pplus 110 M

Mbps, 1100 M

Mbps, 11000 M

Mbps EEthernet 

and 110/100 SSwitching EEthernet M

Media C

Conversion M

Modules

LE7401A-R2
LE7404A
LE7408A
LE7412A
LE7412A-DC
LE740-TPSTM-R2
LE740-TPSTM-SC-R2

LE740-TPSTS20-R2
LE740-TPSCS20-R2
LE740-TPBNC
LH740-TPSTM-R2
LH740-TPSCM-R2
LH742-TPSTM-SX
LH740-TPSTS20-R2

LH740-TPSCS20-R2
LH741-TPSTSXM
LH741-TPSCSXM
LH741-TPSTM
LH741-TPSCM
LH741-TPSM
LH741-TPSCS13/15

LH741-TPSCS15/13
LH741-TPSCS13/1540
LH741-TPSCS15/1340
LG741-TXSXSC
LG741-TXLXSC
LG741-TXLXSC40
LG741-TXLXSC70

LG741-TXLXSC-13
LG741-TXLXSC-15
LG741-TXLXSC-1340
LG741-TXLXSC-1540

1000 Park Drive • Lawrence, PA  15055-1018 USA

TEL: (724) 746-5500 • FAX: 724-746-0746

info@blackbox.com • www.blackbox.com

© 1992-2005 Black Box Corp.  All rights reserved.

The information in this document is subject to change without notice.  Black Box assumes no responsibility for any errors that may
appear in this document.  All product names are trademarks of the manufacturer.  Specific brands and product names may be trade-
marks and are the property of their respective companies.

Document Number 51-80780BB-02 A0

October 2005

Summary of Contents for LE740-TPSTM-R2









Reviews: