2
15
About 100Mbps Media Conversion Modules
100Mbps Media Conversion Modules
provide a single conversion between
100Base-TX twisted pair and 100Base-FX or SX fiber. Each module requires one
slot in a
Media Converter
chassis. The following versions are available:
LH740-TPSTM-R2
TX/FX-MM1300-ST
2 Km
LH740-TPSCM-R2
TX/FX-MM1300-SC
2 Km
LH742-TPSTM-SX
TX/SX-MM850-ST
300 m
LH740-TPSTS20-R2
TX/FX-SM1310/PLUS-ST
40 Km
LH740-TPSCS20-R2
TX/FX-SM1310/PLUS-SC
40 Km
NOTE: All modules support half- and full-duplex.
10/100 Mbps Switching Media Conversion Modules
The auto-negotiating, 10/100 switching media converter offers plug-and-play
operation, converting 10Base-T or 100Base-TX, Half- or Full-Duplex twisted pair to
100Base-FX, Full-Duplex fiber. This module protects against Broadcast storms, and
allows jumbo packets of up to 1916 bytes. The following versions are available:
LH741-TPSTSXM
TP-TX/FX-MM850-ST
300 m
LH741-TPSCSXM
TP-TX/FX-MM850-SC
300 m
LH741-TPSTM
TP-TX/FX-MM1300-ST
2 Km
LH741-TPSCM
TP-TX/FX-MM1300-SC
2 Km
LH741-TPSM
TP-TX/FX-SM1310/PLUS-SC
40 Km
LH741-TPSCS13/15
TP-TX/SSFX-SM1310-SC
20 Km
LH741-TPSCS15/13
TP-TX/SSFX-SM1550-SC
20 Km
LH741-TPSCS13/1540
TP-TX/SSFX-SM1310/PLUS-SC
40 Km
LH741-TPSCS15/1340
TP-TX/SSFX-SM1550/PLUS-SC
40 Km
1000Mbps Media Conversion Modules
1000Mbps Media Conversion Modules
provides a single-conversion
between 1000Base-T twisted pair and 1000Base-LX or SX fiber. These mod-
ules offer plug-and-play operation, and always operates at Full-Duplex.
Each
Gigabit
module requires one slot in a
MediaConverter
chassis.
LG741-TXSXSC
TX/SX-MM850-SC
300 m
LG741-TXLXSC
TX/LX-SM1310-SC
10 Km
LG741-TXLXSC40
TX/LX-SM1310/PLUS-SC
40 Km
LG741-TXLXSC70
TX/LX-SM1550/LONG-SC
70 Km
LG741-TXLXSC-13
TX/SSLX-SM1310-SC
10 Km
LG741-TXLXSC-15
TX/SSLX-SM1550-SC
10 Km
LG741-TXLXSC-1340
TX/SSLX-SM1310/PLUS-SC
40 Km
LG741-TXLXSC-1540
TX/SSLX-SM1550/PLUS-SC
40 Km
Configuring Media Conversion Modules
Before installing, you can configure
10Mbps
and
100Mbps Modules
for
a variety of features (see diagrams/chart on page 3-4 for specific informa-
tion).
10/100 Switching
and
Gigabit Modules
have plug-and-play operation
and require no configuration.
F
E D E R A L
C
O M M U N I C A T I O N S
C
O M M I S S I O N
R
A D I O
F
R E Q U E N C Y
I
N T E R F E R E N C E
S
T A T E M E N T
This equipment has been tested and found to comply with the limits for a Class A com-
puting device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which the user will be required to correct the
interference at his own expense.
Any changes or modifications not expressly approved by the manufacturer could void the
user's authority to operate the equipment.
The use of non-shielded I/O cables may not guarantee compliance with FCC RFI limits.
This digital apparatus does not exceed the Class A limits for radio noise emission from
digital apparatus set out in the Radio Interference Regulation of the Canadian Department of
Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites
applicables aux appareils numériques de classe B prescrites dans le Règlement sur le brouil-
lage radioélectrique publié par le ministère des Communications du Canada.
