background image

MAIN FRAME PARTS

Base Panel (Center) – (1)

Base Panel (Front & Back) – (2)

Side Panels – (2)

Side Panels – (2)

Front Panel – (1)

Rear Panel – (1)

PARTS AND HARDWARE IDENTIFICATION

LOWER FRAME ASSEMBLY

Frame Tube  Connectors – (2)

Rear Axle Assembly – (1)

Front Axle Assembly – (1)

Side Panel Brackets – (2)

Connector Brackets – (4)

Straight Support Brackets(Center) – (4)

Angled Support Brackets (Right) – (2)

Angled Support Brackets (Left) – (2)

16” Pneumatic Tires W/Rims – (4)

HANDLE ASSEMBLY

Tractor Pull Handle – (1)

ASSEMBLY HARDWARE

Bolts 10 x 20mm – (20) 

16 for connector brackets, 4 pre-assembled to angled support brackets

Bolts 10 x 35mm – (4) 

for straight support brackets

Bolts 10 x 60mm – (8) 

for straight and angled support brackets

Bolts 8 x 20mm – (2) 

for side panel brackets

Bolts 10 x 50mm – (8) 

for installing tube connectors to front and rear axle frame

Bolts 12 x 60mm – (1) 

for installing pull handle

Bolts 12 x 80mm – (1) 

pre-assembled to front axle assembly

Lock Nuts 10mm – (40) 

Lock Nuts 8mm – (6) 

4 pre-assembled lock handles, 2 for side panel brackets

Lock Nuts 12mm – (2) 

1 for installing tractor pull handle. 1 pre-assembled to front axle assembly

Washers 8mm – (6) 

2 for side panel brackets, 4 pre-assembled to lock handles

Washers 10mm – (40) 

Washers 12mm – (2) 

1 for installing pull handle, 1 pre-assembled to front axle assembly

Washers 20mm – (6) 

4 used on wheels, 2 pre-assembled to front axles

Pins 80mm – (12) for attaching side panels to base panels

Pins 100mm – (2) 

for attaching side panels to side panel brackets

Clips – (14) 

for use with 80mm & 100mm pins

Small Cotter Pins – (2) 

pre-assembled on front axle assembly

Large Cotter Pins – (6) 

4 for retaining wheels, 2 pre-assembled to front axle assembly

Small Clevis Pins – (2) 

pre-assembled on front axle assembly

Large Clevis Pin – (1) 

pre-assembled on tractor pull handle

Clevis Clip – (1) 

pre-assembled on tractor pull handle

Lock Handles 8mm – (4) 

pre-assembled on front and rear panels

30

31

32

33

34

35

36

37

14

1B

1A

2A
2B

3
4

6

11
12
13

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

7
8
9

10

5

Summary of Contents for MH1100







Reviews: