Black+Decker BDROUT127, Manual

•  Never  use  router  bits  with  a  diameter 

exceeding  the  maximum  diameter 

specified in the technical data section.

•  Do  not  use  the  tool  in  an  inverted 

position.

•  Refer  to  Fig  1-2  on  page  4  for  changing 

the collet.

•  Do  not  attempt  to  use  the  tool  in  a 

stationary mode.

•  If the supply cord is damaged, it must be 

replaced  by  the  manufacturer  or  an 

authorised  BLACK+DECKER  Service 

Centre in order to avoid hazard.

•  Take special care when routing where the 

paint  is  possibly  lead  based  or  when 

routing some woods which may produce 

toxic dust:

-  Do  not  let  children  or  pregnant  women 

enter the work area.

-  Do  not  eat,  drink  or  smoke  in  the  work 

area.

- 

Dispose  of  dust  particles  and  any  other 

debris safely.

•  The  intended  use  is  described  in  this 

instruction  manual.  The  use  of  any 

accessory or attachment or performance 

of any operation with this tool other than 

those  recommended  in  this  instruction 

manual  may  present  a  risk  of  personal 

injury and/or damage to property.

Safety of others

•  This  appliance/tool  is  not  intended  for 

use  by  persons  (including  children)  with 

reduced  physical,  sensory  or  mental 

capabilities,  or  lack  of  experience  and 

knowledge,  unless  they  have  been  given 

supervision or instruction concerning use 

of the appliance by a person responsible 

for their safety.

•  Children  should  be  supervised  to  ensure 

that they do not play with the appliance.

Residual risks

Additional  residual  risks  may  arise  when 

using the tool which may not be included in 

the  enclosed  safety  warnings.  These  risks 

can arise from misuse, prolonged use etc.

Even  with  the  application  of  the  relevant 

safety  regulations  and  the  implementation 

of  safety  devices,  certain  residual  risks  can 

not be avoided. These include:

•  Injuries  caused  by  touching  any 

rotating/moving parts.

•  Injuries caused when changing any parts, 

blades or accessories.

•  Injuries caused by prolonged use of a

  tool.  When  using  any  tool  for  prolonged 

periods ensure you take regular breaks.

•  Impairment of hearing.
•  Health  hazards  caused  by  breathing  dust 

developed  when  using  your  tool 

(example:- working with wood, especially 

oak, beech and MDF.)

Labels on tool

The label on your tool may include the 

following symbols along with the date code:

Position of Date Code

The Date Code, which also includes the year 

of manufacture, is printed into the housing.
Example:

2017 XX JN

Year of manufacturing

Electrical safety

This  tool  is  double  insulated; 

therefore  no  earth  wire  is  required. 

Always  check  that  the  power  supply 

corresponds  to  the  voltage  on  the 

rating plate.

•  If the supply cord is damaged, it must be 

replaced  by  the  manufacturer  or  an 

authorised  BLACK+DECKER  Service 

Centre in order to avoid a hazard.

17

ENGLISH

(Original instructions)

Hz ....... 

Hertz

W ....... 

Watts

min ..... 

minutes

       ..... 

Alternating

Current

        .....  Direct 

Current

 Read

Instructions

Manual

 Use Eye

Protection

 Use Ear

Protection

           ......  Class II

Construction

          ......  Earthing

Terminal

         ......  Safety

Alert Symbol

.../min..  Revolutions 

or Recipro-

cation per

minute

V ........     Volts

A ........    Amperes 

n

0

 .......    No-Load 

               Speed