background image

4

As soon as you have purchased the inflator, we 
recommend that you check to make sure it is 
intact and that you read the operating instructions 
carefully before using it.  The purchase receipt 
for this product is to be retained and must be 
presented if making a claim under the terms of 
the Smart Marketing Group (SMG) warranty.  Bank 
account statements are not acceptable for proof of 
purchase.
This warranty does not cover inflators intended 
for hire or use in commercial applications or in 
commercial premises.  The warranty will under 
no circumstances extend to reimbursement or 
payment of damages, whether direct, indirect 
or consequential.  The warranty is void if there 
is evidence the inflators has been modified
or tampered with in any way or used with 
unauthorised accessories without our consent.
SMG declines any responsibility or liability 
whatsoever arising from misuse or abuse, 
negligent handling of the inflators or if the 
product has not been installed or failure to 
comply with the relevant safety, operating, 
setting and maintenance instructions (see 
further in this manual).
Any item sent freight collect for repair will 
be refused.  Warranty repairs are free of 
charge, provided the appliance is delivered to 
our service department or authorised service 
agent.  The inflator will need to be returned, 
adequately protected in a box. Transit damage 
is responsibility of the owner.  Assistance under 
the warranty will only be made available if the 
request is made to our customer service team 
on the contact numbers listed below and proof of 
purchase is provided.
This is a repair only warranty you will need to take 
the inflator to the authorised service agent after 
contacting our customer service centre.
Damage caused by third party accessories is not 
covered under this warranty.

Damage caused to attached equipment or third 
party accessories will not be covered under this 
warranty.
Rust and corrosion are not covered under  
this warranty.
If a warranty fault is found the freight cost will 
be credited to the owner. Blockages caused by 
spider webs, insects, dirt, or accumulated dust 
is not covered by warranty.  SMG reserves the 
right to replace or repair the appliance within 
the warranty period. Parts found to be defective 
due to a manufacturing default will be replaced 
free of charge.
In the event of SMG choosing to replace the 
appliance, the warranty will expire at the original 
date of purchase.  If no warranty fault is found 
the owner will be advised and the product will be 
returned and any costs associated with the service 
will be charged to the owner.
In Australia, this SMG warranty is in addition 
to the conditions and guarantees which are 
mandatory as implied by the Trade Practices Act 
1974 and State and Territory legislation.
In New Zealand, this SMG warranty is in addition 
to the conditions and guarantees which are 
mandatory as implied by the New Zealand 
Consumer Guarantee Act 1993.
For service, spare parts or product information 
please contact customer service:
Australia: 1300 660 457
New Zealand: 0800 474 876

COMPLETE WARRANTY STATEMENT – INFLATOR GROUP

Summary of Contents for BRI40

















Reviews: