3
To exit Valet Mode:
1. Turn the ignition key on.
2. Press and hold the valet/service mode
switch for 3 seconds.
• The LED will turn off.
• The Siren will chirp 2 times.
EMERGENCY OVERRIDE
If the transmitter becomes lost or fails to
operate, the system can be disarmed by using
the emergency override feature.
To override the system:
1. Enter the vehicle.
• Because the system is armed, the siren
will sound.
2. Turn on the ignition key.
3. Press the Valet/Service Mode switch.
• The siren will stop sounding.
REMOTE PANIC
In the event of an emergency (PANIC)
situation, the system’s siren can be triggered to
attract attention. To activate the Panic Feature,
press transmitter button 1 for 3 seconds:
• The siren will sound .
• The parking lights will flash.
The Panic mode will run for 45 seconds, or
until transmitter button 1 is pressed again.
The Panic Feature will not operate when the
ignition is on. Also, if the vehicle is Remote
Started, activating the Panic Feature will shut
down the Remote Start.
STATUS CONFIRMATION
To confirm the system’s current status (Armed,
Disarmed, Started, etc.) press transmitter
Button 3. The transmitter will beep, and the
LCD will provide a text display of the current
condition of the system.
See Transmitter
Indications.
TRUNK RELEASE
Press button 3 for approximately 2 seconds to
open the trunk.
TRUNK DISARM FEATURE
The trunk disarm feature allows the alarm to
disarm automatically when transmitter button
3 is used to activate the trunk release. This
eliminates having to first disarm the alarm
before activating the trunk release.
This feature
must be programmed during installation.
CAR LOCATOR FEATURE
The Car Locator feature allows the parking
lights to stay on for 30 seconds instead of
flashing when the alarm is disarmed.
This feature
must be programmed during installation and is not
recommended for vehicles with additional
aftermarket or auxiliary lighting.
Remote Start Operation
Important:
The system should be placed
into the valet mode when parked inside a
garage or being left for service. Only start
the vehicle in a well ventilated area. Do not
use in a closed garage or indoors. Be sure to
familiarize yourself with all features prior to
using this product.
REMOTE STARTING THE VEHICLE
To remote start the vehicle:
Press and hold transmitter button 2 for two
seconds.
• The siren will chirp 3 times.
• The parking lights will turn on.
• The engine will crank.
• Once the car has started, the heater or air
conditioner will turn on and run for the
preprogrammed time (15 or 25 minutes).
If the engine fails to start on the first
6
3 until the transmitter beeps five times
and CHIRP is displayed.
2. Release the transmitter buttons.
• The display will show ON or OFF to
indicate the chirp status.
• The parking lights will flash once to
indicate silent operation.
• The siren will chirp and the parking
lights will flash to indicate normal
operation.
CONFIRMATION BEEP
To turn the transmitter’s confirmation tones on
or off:
1. Press and hold transmitter buttons 2 and
3 until the transmitter beeps six times and
SOUND is displayed.
2. Release the transmitter buttons.
• The display will show ON or OFF when
to indicate the beep status.
NOTE:
Pressing transmitter button 2 during a
confirmation tone will immediately mute the tone.
BACKGROUND ILLUMINATION
To turn on the LCD background illumination
press transmitter button 2.
STATUS INDICATOR (LED) FUNCTIONS
On Solid = Valet Mode
Slow Flash = System Armed
Rapid Flash = Passive Arming
Flash 2x = Remote Start
Flash 3x = Stop and Go Mode
Flash 5x = Cold Start Mode
PARKING LIGHTS FUNCTIONS
On Solid = Vehicle Remote Starting
Flash 1x = Doors Locked
Flash 2x = Doors Unlocked
Flash 3x = Open Zone Indication (after arming)
Flash 5x = Auto Cold Start Engaged
SYSTEM REFERENCE INDICATORS