background image

Remote Programmable Features

To enter program mode:

1. Turn ignition to the on position.
2. Wait 2 seconds.
3. Within 10 seconds press program switch 5

times.

4. The siren will give one long chirp indicating

the system is now in program mode.

To change programmable features:
Press program switch the number of times that
equal to the feature you wish to change. The
siren will chirp each time the switch is pushed.
(Example: to turn feature #3 off press the
program switch 3 times).

• Press button 1 on the remote to turn the

feature on, the siren will chirp once.

• Press button 2 on the remote to turn

feature off. Siren will chirp twice.

System will automatically exit program mode.

NOTE:

You must re-enter program mode for

each feature you wish to change.

Programmable Features

Program #1: Arming Mode

On = Passive
Off = Active 

Program #2: Passive Lock

On = Passive w/lock
Off = Passive no lock 

Program #3: Auto Re-arm

On =  Auto Re-arm enabled
Off =   Auto Re-arm disabled

Program #4: Normal/Silent Arming

On = Normal operation 
Off = Silent operation

Program #5: Door Unlock Pulse

On = Single
Off = Double

Program #6: Door Lock Pulse Length

On = 0.7 second door lock/unlock pulse
Off = 3 second door lock/unlock pulse 

Program #7: Ignition Lock

On = Ignition auto lock
Off = No ignition auto lock

Program #8: Auto Cold Start Defeat

On = Disable Auto Cold Capability
Off = Enable Auto Cold Capability

Program #9: Cold Start Timing

On = Cold start every 2 hours 
Off = Cold start every 1 hour

Program #10: Trunk Disarm Feature 

On = Disabled
Off = Enabled

Program #11: Passive Arm Warning Chirps Delete

On = Passive arming without warning chirps
Off = Passive arming with warning chirps

Program #12: Open Zone Chirp Timing

On = Standard - 10 seconds
Off = Delayed - 60 seconds 

Program #13: Remote Start Run Time

On = 15 minutes
Off = 25 minutes

Program #14: Lock Before & After Engine Crank

On = Lock when remote start activates
Off = Disabled

Program #15: Door Lock After Shut Down

On = Lock when remote start shuts down
Off = Disabled

Program #16: Parking Light Operation

On = Normal 
Off = Car finder feature

5

Summary of Contents for 250













Reviews: