background image

3

STOP AND GO

The Stop and Go feature allows the vehicle to

remain running without use of the ignition key

during short stops.
To activate the Stop and Go feature:

1. Make sure the engine is running.
2. Press button 3.
3. Turn ignition off.

• The doors will unlock.

• The parking lights will turn on.

• The engine will remain running.

4. Exit the vehicle and lock the doors using

transmitter button 1.

To resume driver control:

1. Unlock the doors by pressing transmitter

button 2.

2. Turn on the ignition.

• The vehicle resumes driver control,

when the brake pedal is pressed.

AUTO COLD START

This feature allows the system to start and run

the vehicle every 2, 3, or 4 hours (user

selectable) for up to 12 starts. This allows the

engine to remain at an operational temperature

in extremely cold weather. Auto Cold Start

interval timing must be chosen during

installation.
Engaging the Auto Cold Start feature:

To turn Auto Cold Start on:

1. Press and hold buttons 1 & 3 together for

3 seconds.
• The parking lights will turn on for 10

seconds to confirm activation.

2. Press the button corresponding to the

desired start cycle interval:

Button 2 = start every 2 hours

Button 3 = start every 3 hours

Button 4 = start every 4 hours

• The parking lights will flash a number

of times equal to the chosen interval.

Disengaging the Auto Cold Start feature:
Any of the following actions will cancel the

Auto Cold Start feature:

Press and hold buttons 1 & 3 together for 3

seconds.

• The parking lights will flash twice and

the horn will honk twice (optional) to

confirm deactivation.

- or -

Press the brake pedal.

- or -

Turn ignition on.

SAFETY FEATURES

The System will not start the vehicle if the

brake pedal is pressed, if the hood is open, or if

the system is in Valet mode.Also, if the brake is

pressed or the hood is opened while remote

running, the remote start will shut down.

LED AND PARKING LIGHT 

DIAGNOSTIC 

INDICATIONS 

Parking Light

LED Indication

Problem

3 Slow Flashes 

On Solid

System in Valet Mode

5 Slow Flashes

No Flashes

Key is on during remote start attempt

5 Flashes

5 Flashes

Open hood warning (before start)

5 Flashes

5 Flashes

System shut down using brake pedal (when running)

7 Flashes

7 Flashes

Tachometer lock out (see dealer)

BW651 final.qxd  10/18/2005  10:58 AM  Page 3

Summary of Contents for 651













Reviews: