background image

2

PASSIVE STARTER DEFEAT 

If the optional starter defeat is installed, the

system can be programmed to automatically

disable the starter 45 seconds after turning

off the ignition as an extra measure of

security in the event the vehicle is

accidentally left unlocked. During the 45

second countdown, the LED will flash rapidly

to indicate the passive starter defeat

sequence has begun. After 45 seconds, the

LED will flash slowly and the vehicle’s starter

will be disabled.

IGNITION TRIGGER

After the system is remotely locked, turning

on the ignition before remotely unlocking

the system activates the optional ignition

trigger feature (if selected during

installation). The horn will honk and the

parking lights will flash for 30 seconds. To

deactivate the feature once triggered, press

button 2 on the transmitter or use the

override procedure (see below).

HORN OUTPUT

If the optional Horn Honk feature is

connected, the horn will provide

confirmation chirps when locking or

unlocking the doors, or when the Panic

feature is activated.

REMOTE PANIC

If the optional horn honk output is installed,

pressing button 4 for three seconds will

trigger the  Panic mode.The horn will honk

and parking lights will flash for 30 seconds, or

until button 4 is pressed again.

EMERGENCY OVERRIDE

If the optional starter defeat is installed and

your remote is lost or fails to operate, you

can manually override the starter defeat.

Turn on the ignition, then press  the

override/valet switch for two seconds. The

starter defeat will disengage and the system

will enter valet mode.

VALET MODE

When the system is placed into valet mode,

the optional starter defeat, ignition trigger,

and passive starter defeat will be disabled.To

put your system into valet mode, turn the

ignition on and hold the override/valet

switch for 3 seconds. The horn will chirp

once (if installed) and the LED will turn on

solid to confirm valet mode. To exit valet

mode, repeat the same procedure. The horn

will chirp twice and the LED will turn off to

confirm valet mode exit.

AUXILIARY OUTPUT

The auxiliary output may be used to activate

an optional feature such as trunk release.

Press and hold button 3 for three seconds to

activate.

ILLUMINATED ENTRY

The optional Illuminated Entry turns on the

dome light when the doors are remotely

unlocked. The dome light will remain on for

30 seconds or until the ignition is turned on.

LED STATUS MODES

Locked = Slow flash
Disarmed = Off
Passive Starter Defeat Warn = Rapid flash
Valet Mode = Solid

853 new.qxd  3/15/2004  12:44 PM  Page 2

Summary of Contents for BW 853









Reviews: