background image

4

• BLUE/WHITE WIRE - Passenger unlock

output (-) 500mA. The BLUE/WHITE wire

provides a ground to unlock the passenger

doors when the unlock button on the

transmitter is pressed two times. To install

the two-step unlock feature,

the

BLUE/BLACK and BROWN/BLACK wires

must be run directly to the driver’s door

actuator unlock wire and the BLUE/WHITE

wire must be connected to a relay to unlock

the passenger doors.

(see Optional Two-Step

Unlock Diagrams)

• YELLOW WIRE - Ignition input (+).

Connect to the main ignition wire that

sw12V and does not drop out during

cranking.

2-Pin Red Connector:

Plug-in connector

port for LED. Mount LED in an area where

it may be easily seen from either side of the

vehicle.

2-Pin Blue Connector:

Plug-in connector

port for program/service switch. Mount

program switch in an area that is easily

accessible from the driver’s position.

PROGRAMMABLE FEATURES

To enter program mode:

1. Turn on ignition.
2. Within 5 seconds, press valet switch 5

times.
• The horn will provide a long chirp, to

indicate entering program mode.

3. Press the valet switch the number times

equal to the desired feature.
• The horn will chirp and lights/LED will

flash, each time the valet switch is

pressed.

4. Within 5 seconds, press the transmitter

button corresponding to the desired

operating mode for that feature.
• The horn will chirp and lights will flash

to indicate the setting.

One chirp/flash = Button 1
Two chirps/flashes = Button 2

5. Turn off ignition to save changes.

FEATURE DESCRIPTION

1. Ignition Lock/Unlock. Automatically

locks the doors when the ignition is turned

on and unlocks when the ignition is turned

off.
2. Door Unlock Pulse. Selects between a

single or double unlock pulse.
3. Chirp Mode. Selects or bypasses the

system’s lock’unlock confirmation chirps.
4. Door Lock PulseLength. Selects

between a .75-second or 3-second

lock/unlock pulse.
5. Passive Starter Defeat. Enables the

starter defeat to automatically activate 45

seconds after turning off the ignition.
6. Ignition Trigger. Enables the ignition

trigger feature when the system is remotely

locked.

Remote Programmable Features:

Step

Function

Button 1 (Default)

Button 2

1.

Ignition Controlled Door Locks

On

Off

2.

Door Unlock Pulse

Single

Double

3.

Chirp Mode

Standard

Silent

4.

Door Lock Pulse Length

.75 Seconds

3 Seconds

5.

Passive Starter Defeat Enable

Off

On

6.

Ignition Trigger Feature

Off

On

Summary of Contents for BW 854









Reviews: