background image

2

PASSIVE ARMING

The passive arming feature automatically

arms the system after closing all doors. The

Passive Arming feature requires the ignition

to have been on for at least 10 seconds prior

to exiting the vehicle. This enables the key to

be turned on then off quickly to avoid

passive arming in the event of refueling,

washing the vehicle, etc.

The Passive Arming

feature may be enabled during installation.

To arm the system passively:

1. Turn the ignition key off (make sure

ignition was on for at least 10 seconds).

2. Exit the vehicle and close all doors.

• The LED flashes rapidly indicating

that the system is preparing to arm.

(The system can be armed any time

by pressing transmitter button 1.)

• If the optional countdown feature is

programmed, the siren will chirp

every 2 seconds until armed.

• The siren will chirp 30 seconds after

the last door is closed to indicate the

system is armed. NOTE: Opening a

door resets the passive arming timer.

• The doors will lock.†*

If Passive Locking was enabled during installation.

DISARMING OPERATION

To disarm the system press transmitter

button 2.

• The siren will chirp twice.

• The parking lights will flash twice.*

• The doors will unlock.*

• The dome light will turn on for 30

seconds.*

TAMPER ALERT 

If the alarm was triggered while away from

the vehicle, the siren will chirp 3 times and

the parking lights will flash 3 times on

disarming for tamper indication.

AUTO REARM 

The Auto Rearm feature allows the system to

automatically re-arm and lock the doors* in

the event the system is disarmed and a door

is not opened within 30 seconds.

This

programmable feature may be enabled during

installation.

SILENT ARMING/DISARMING

Press transmitter button 3 to silently Arm or

Disarm the system for one-time operation.

The system can also be programmed for full-

time silent operation during installation.

IGNITION LOCK*

The ignition locking feature automatically

locks the doors 5 seconds after the ignition

key is turned on, and automatically unlocks

when the ignition key is turned off. To avoid

locking keys in the vehicle, the ignition

locking feature will be cancelled if a door is

open when the ignition is turned on.

This

feature may be disabled during installation.

REMOTE PANIC

In the event of an emergency (PANIC)

situation, the system’s siren can be triggered

for 30 seconds to attract attention. To activate

the Panic Feature, press transmitter button 1

for 3 seconds:

• The siren will sound.

• The parking lights will flash*.

Press button 1 to exit panic mode and rearm

the system. Press button 2 to exit panic

mode and disarm system.The Panic Feature

will not operate when the ignition is on.

*

Optional feature 

Summary of Contents for BW2900R2

















Reviews: