background image

Firmware Version 6 

 

This product uses satellite and terrestrial technologies that are inherently subject to 
transmission and reception limitations, and will operate intermittently under certain 
environmental conditions.  Extreme weather or objects that prevent an unobstructed view of the 
sky may restrict reception or transmission of messages as well as acquisition of your global 
positioning system (GPS) coordinates.  In addition, service may become limited or temporarily 
unavailable due to equipment failures or outages by the service providers.  Accordingly, 
Blackbird cannot guarantee that the product will operate without interruption. 

The BAT device integrates with Blackbird Technologies’ Gotham system.  The Gotham system 
is a comprehensive back-end solution for monitoring, operating, and managing tagging, 
tracking, and locating (TTL) devices and viewing associated geospatial data.   

For information about Blackbird’s other TTL products and services, and for technical support, 
contact the Blackbird Help Desk through the following email address: 

ttl-help@blackbirdtech.com 

 

 

Copyright 2010, Blackbird Technologies, Inc. 

 

All Rights Reserved 

Rev B 

 

Summary of Contents for Blackbird Asset Tracker













Reviews: