background image

F

E A T U R E S

 Laundry Installation and Setup Guide 

38

F

E A T U R E S

F

EATURES

• Includes 15-key keypad and an 8-line x 21 character LCD display

• Contains a keyed lock to secure the inside of the unit, along with a hinged door to access the circuit boards (

If 

you prefer a high security lock or unique keys, you can purchase Medeco 60W-0750-239 from RA-LOCK 
Company (800-777-6310.)

• Supports 10/100Base-T or RS-485 Communication

• Supports wired or 2.46Hz wireless communication to laundry machines

• Compatible with both Universal and Unix Editions of BbTS

Table 4: LC3000 Component Specifications

LC3000

Power

Input Voltage Range

 

Input Frequency

 

Input Current

120VAC
60Hz

 

1.4A, max

Operating Environment Temperature

Relative Humidity
Altitude

0 to +45C (+32 to +114F)
0 to 95 percent, non-condensing
0 -10,000 feet

Non-Operating 
Environment

Temperature
Relative Humidity
Altitude

-20 to +70 C (-4 to +158F)
0 to 95 percent, non-condensing
0 - 35,000 feet

LE3/PSENCL

with LCM20

Power

Input Voltage Range

 

Input Frequency

 

Input Current

120VAC
60Hz

 

1.4A, max

Operating Environment Temperature

Relative Humidity
Altitude

0 to +45C (+32 to +114F)
0 to 95 percent, non-condensing
0 -10,000 feet

Non-Operating 
Environment

Temperature
Relative Humidity
Altitude

-20 to +70 C (-4 to +158F)
0 to 95 percent, non-condensing
0 - 35,000 feet

LE3/BRIDGE

Power

Input Voltage Range

 

Input Frequency

 

Input Current

9 to 30 VAC or 7 to 36 VDC
60Hz

 

0.12A, max

Operating Environment Temperature

Relative Humidity
Altitude

0 to +45C (+32 to +114F)
0 to 95 percent, non-condensing
0 -10,000 feet

Non-Operating 
Environment

Temperature
Relative Humidity
Altitude

-20 to +70 C (-4 to +158F)
0 to 95 percent, non-condensing
0 - 35,000 feet

LWI3xxx

Power

Input Voltage Range

 

Input Frequency

 

Input Current

9 to 30 VAC or 7 to 36 VDC
60Hz

 

0.12A, max

Operating Environment Temperature

Relative Humidity
Altitude

0 to +45C (+32 to +114F)
0 to 95 percent, non-condensing
0 -10,000 feet

Non-Operating 
Environment

Temperature
Relative Humidity
Altitude

-20 to +70 C (-4 to +158F)
0 to 95 percent, non-condensing
0 - 35,000 feet

Summary of Contents for LC3000












































Reviews: