background image

S E 3 - R D R 1 0 0  I

N S T A L L A T I O N 

G

U I D E

D

O C U M E N T 

1 2 9 1   

R

E V 

0 1

P

RINTED

 N

OVEMBER

 24, 2009                 

1-1

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device 

may not cause harmful interference, and (2) this device must accept any interference received, including interference that 

may cause undesired operation. 

Part 15.21: Changes or modifications not expressly approved by the party responsible for complianc

rity 

to operate the equipment.

NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. 

This equipment complies with the FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the 

specific operating instructions for satisfying RF exposure compliance. The antenna(s) used for this transmitter must be installed to 

provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other 

antenna or transmitter.

Blackboard Inc.

SE3-RDR100

Tested To Comply
With FCC Standards

FOR HOME OR OFFICE USE

This Class B digital apparatus complies with 

Canadian ICES-003

Cet appareill numérique de la classes B est conform 

à la norme NMB-003 du Canada

Summary of Contents for SE3-RDR100














Reviews: